Advertisement

Quick Links

Pinner™ Series
Arc Resistant
Pinner Applicators
INSTALLATION AND OPERATING INSTRUCTIONS
PI NNE R APPLICATO R S
5 2 0 0 6 4 7 R e v G

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Simco-Ion Pinner Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ITW Simco-Ion Pinner Series

  • Page 1 Pinner™ Series Arc Resistant Pinner Applicators INSTALLATION AND OPERATING INSTRUCTIONS PI NNE R APPLICATO R S 5 2 0 0 6 4 7 R e v G...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS 1. SAFETY ......................3 2. INTRODUCTION ....................3 Features and Benefits .....................3 How Pinners Work ....................4 Receipt of Equipment ....................4 Return Shipments ....................4 3. SPECIFICATIONS ....................5 4. INSTALLATION ....................5 Standard Installation ....................5 Installation with Optional Mounting Stand (P/N 5051082) .........6 High Voltage Wire Routing ...................6 5.
  • Page 3: Safety

    1. SAFETY NOTE – Statements identified with a NOTE indicate precautions necessary to avoid potential equipment failure. CAUTION – Statements identified with a CAUTION indicate potential safety hazards. The following safety procedures must be followed for safe Pinner operation. 1. Read instruction manual before operating or installing device. 2.
  • Page 4: How Pinners Work

    • Rated for use in temperatures to 500°F • Designed and tested as an integral component of Simco-Ion electrostatic charging systems How Pinners Work Simco-Ion’s electrostatic charging power supplies provide high voltage to the Linear Pinner, 5-Point and Pinner Claw points. The electrical stress at the points produce corona which injects ions into the air.
  • Page 5: Specifications

    3. SPECIFICATIONS Overall Length Handle Diameter Linear 4.75” Dimensions 5-Point 6.75” Claw 6.75” Linear Pinner and Pinner Claw: 0.5” x 2.5” to 1” x 5” elliptical; Charge Pattern 5-Point: 1” x 2” circular pattern (kV) 5-Point (µA) Claw (µA) Ion Output Current at 0.5”...
  • Page 6: Installation With Optional Mounting Stand (P/N 5051082)

    You can install the Pinner applicator to the mounting surface using the perforated strip supplied (see Figure 1) or using the mounting plate assembly (P/N 4105581, see Figure 2). NOTE – The mounting clamps for the 5-Point and the Pinner Claw must be at least 2”...
  • Page 7 NOTE – Pinner 5-point, Linear Pinner and Pinner Claw products are rated for use with up to 30kV or ±50kV in special installations with insulation required. Use at high voltages may cause component breakdown and operator shock hazard. Figure 1. Mounting Using Perforated Strips Figure 2.
  • Page 8: Operation

    Figure 4. Assembly details of Pinner Applicator on Mounting Stand Assem bly deta ils of P inn er Appl icator o n M ounting Stand – Figure 4 5. OPERATION Simco-Ion’s Power Supplies provide high voltage to the Pinner 5-Point, Linear Pinner and the Pinner Claw.
  • Page 9: Replacement Parts

    8. REPLACEMENT PARTS Part Part Number Linear Pinner applicator 4009903 Pinner Claw applicator 4008144 5-Point applicator 4004738 Flex Arm mounting assembly 5051082 Mounting plate assembly 4105581 Teflon head and radial pin assembly 5050470 Spring loaded cable connector 4100286 Stainless jumper plug 4640763 Replacement resistor 4590820...
  • Page 10 Simco-Ion 2257 North Penn Road Hatfield, PA 19440 (215) 822-6401 (800) 203-3419 www.simco-ion.com customerservice@simco-ion.com © 2021 Simco-Ion. Printed in the U.S.A. PI NNE R APPLICATO R S 5 2 0 0 6 4 7 R e v G...

Table of Contents