VISIT OUR WEBSITE TO: Get usage advice, brochures, trouble shooter, service and repair information: www.zanussi.com/support SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage.
Do not change the specification of this appliance. • The operating water pressure (minimum and maximum) must be • between 0.5 (0.05) / 8 (0.8) bar (MPa) Follow the maximum number of 13 place settings. • If the supply cord is damaged, it must be replaced by the •...
• Connect the mains plug to the mains socket DISPOSAL only at the end of the installation. Make sure that WARNING! Risk of injury or there is access to the mains plug after the suffocation. installation. • Do not pull the mains cable to disconnect the •...
EASY START On/off indicator Delay button Programme marker Programme knob Indicators Start button INDICATORS End indicator. Salt indicator. It is always off while the programme operates. Rinse aid indicator. It is always off while the programme operates. PROGRAMMES The order of the programmes in the table may not reflect their sequence on the control panel.
SETTINGS ADJUSTING THE WATER SOFTENER The programme marker must be in position. 1. Press and hold and simultaneously turn the knob counterclockwise until the programme marker is in position. 2. Release when and Delay start to flash. • The current setting is indicated by the number of flashes of the indicator (e.g.
The programme marker must be in position. 1. Press and hold and simultaneously turn the knob counterclockwise until the programme marker is in position. 2. Release when and Delay start to flash. 3. Turn the knob counterclockwise until the programme marker is in position.
ADDING SALT Before the first use, put one litre of water in the salt container. CAUTION! Water and salt can come out of the salt container during filling. To prevent corrosion, start a programme immediately after filling the salt container. ADDING RINSE AID The rinse aid helps to dry the dishes without streaks and stains.
ADDING MULTI-TABLETS • Do not fill the salt container and the rinse aid dispenser. • Set the rinse aid dispenser to the lowest position. PROGRAMME SELECTION MODE The appliance must be in Programme selection mode to start a programme. If the control panel does not show this condition, do the Reset.
STARTING A PROGRAMME 1. Open the water tap and close the door. 2. Select a programme. 3. Press OPTION DELAY With this option you can postpone the start of a programme by 3 hours. 1. Set the programme. 2. Press Delay. 3.
OPENING THE DOOR WHILE THE Do not try to close the appliance door APPLIANCE OPERATES within 2 minutes after AirDry Opening the door while a programme is running automatically opens it as this may stops the appliance. It may affect the energy cause damage to the appliance.
Page 14
tablets (e.g. ''All in 1''). Follow the instructions • Always use the correct quantity of rinse aid. on the packaging. Insufficient dosage of rinse aid decreases the • Select a programme according to the type of drying results. Using too much rinse aid results in bluish layers on the items.
• There is enough salt and rinse aid (unless you 2. First remove items from the lower basket, then use multi-tablets). from the upper basket. • The arrangement of the items in the baskets is After the programme is completed, correct.
INTERNAL CLEANING • To maintain the performance of your appliance at its best, we recommend to use monthly a • Carefully clean the appliance, including the specific cleaning product for dishwashers. rubber gasket of the door, with a soft damp Follow carefully the instructions on the cloth.
Page 17
Problem and alarm code Possible cause and solution The anti-flood device is on. • Close the water tap and contact an Authorised • The end indicator flashes 3 times inter- Service Centre. mittently. • indicator flashes continuously. The appliance stops and starts more •...
Page 18
Problem Possible cause and solution Poor drying results. • Tableware has been left for too long inside the closed appli- ance. • There is no rinse aid or the dosage of rinse aid is not suffi- cient. Fill the rinse aid dispenser or set the dosage of rinse aid to a higher level.
Problem Possible cause and solution Limescale deposits on the table- • The level of salt is low, check the refill indicator. ware, on the tub and on the in- • The cap of the salt container is loose. side of the door. •...