Safety and Care Advice Important – Please read these instructions fully before starting assembly • Do not stand or put weight on •To reduce the • Check you have all the likelihood of components and tools listed on the product, this could cause damaging your pages 2 and 3.
Page 3
Components - Panels For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk Please check you have all the panels listed below Cabinet Left side Right side Upright Foldy back x2 (199.8 x 52.9cm) (199.8 x 55.8cm) (191.4 x 49cm) (194 x 89cm) P2973 BO3452.0960...
Page 4
Components - Fittings For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. ZF9995M ZF9995G ZF9995J Not used until door assembly Screw x 2 Euro screw x 24...
Page 6
Assembly Instructions Assembly Instructions Step 1 Step 1 Cabinet assembly Cabinet assembly Screw 9 locking screws B into the holes of the left side 1. Finished front edge Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes.
Page 7
Assembly Instructions Assembly Instructions Step 1 Step 2 Cabinet assembly Cabinet assembly Screw 9 locking screws B into the holes of the right side 2 . Finished front edge Mount hanger rail support K, fasten with 1 screw D. Screw D into the board between two predrilled holes.
Page 8
Assembly Instructions Assembly Instructions Step 1 Step 3 Cabinet assembly Cabinet assembly Mount hanger rail Mount hanger rail support K on the support K on the upright 3, fasten with upright 3, fasten with screw D 1x. Screw D into screw D.
Page 9
Assembly Instructions Step 4 Cabinet assembly Insert 6x Large locking nuts I into the top/bottom 5. 2x Make sure the ‘arrow’ on I is pointing towards the hole in the edge of the top Finished front edge Step 5 Insert 6x Large locking nuts I into the shelf 6.
Page 10
Assembly Instructions Step 7 Cabinet assembly Attach 2x top/bottom 5 with 4x confirmat screws A to the upright 3. Use allenkey V. Finished front edge Finished front edge Finished front edge Step 8 Attach 2x the shelf 6 to the upright 3 with 3x double locking screws G.
Page 11
Assembly Instructions Assembly Instructions Step x Step 9 Xxxxxx Cabinet assembly Attach the left side 1 with 9x locking screws and locking nuts to the top 5, shelf 8 and the bottom 6. Use a screwdriver to turn 9x locking nuts clockwise to lock.
Page 12
Assembly Instructions Step 11 Cabinet assembly Attach 2x foldy back 4 to back of cabinet with the coloured surface facing the inside of the cabinet using 60x nails F and C C C 26x screws C. Use nail holder N to hold the nails F vertical and at correct distance as you secure the 2x foldy back...
Page 13
Assembly Instructions Step 13 Cabinet assembly Position Top guide rail Q onto top 5, with the ends fitting into support left f and support right g. Fix top guide Q rail with 7x screws C to the top/ bottom 5. Step 14 Insert covercap e into slots of top guide rail Q.
Page 14
Assembly Instructions Step 15 Cabinet assembly Position the lip of bottom guide rail R onto the top of top/bottom 5, fix with 7x screws c. Step 16 Place Hanger rail P onto hanger rail support K. 2x...
Page 15
Assembly Instructions Step 17 Place cabinet Before fixing the unit to the wall, use a spirit level to check if the base of this unit is level front-to-back and side-to-side in the SNAP! three positions shown. Use pegs L to square your unit.
A Guide to - Wall Mounting & Fixings Important: When drilling into walls always Important note: check that there are no hidden wires or pipes etc. If plastic wall plugs Make sure that the screws and wall plugs being used are supplied with your are suitable for supporting your unit.
Need help?
Do you have a question about the Bergen 180 and is the answer not in the manual?
Questions and answers