Page 1
PARTS & SERVICE MANUAL DIESEL SUPER RAKE Model 17-001-C Bunker Rake Starting Serial #2636 December, 2002 SMITHCO PRODUCT SUPPORT 1-800-891-9435 Hwy SS and Poplar Avenue, Cameron WI 54822 E-mail: productsupport@smithco.com...
Serial Number and Model Number. Both numbers are needed when ordering parts. The serial number plate on the Diesel Super Rake is located on the right side main frame. Refer to engine manual for placement of engine serial number.
19. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase. 20. Use parts and materials supplied by SMITHCO only. Do not modify any function or part. These machines are intended for professional maintenance on golf courses and baseball fields. Other use is...
SPECIFICATIONS WEIGHTS AND DIMENSIONS Length with Rake 85" (216 cm) Width with Rake 73.5" (187 cm) Height 44" (112 cm) Wheel Base 47" (119 cm) Weight 990 lbs (449 kg) SOUND LEVEL AT 3200 RPM At ear level 96 dB At 3 ft (0.914 m) 90 dB At 30 ft (9.14 m)
13-111 Drag Mat Kit 13-199* Edger Kit 42-550 Green Star Total RBS System 13-438 Rake Assembly 42-503 RBS Mount for Smithco Super Rake 13-606 Rake Assembly with Lexan Blades 42-530 22-11.00 x 8 Turf Track R/S Tire 42-026 84" Stainless Steel Tournament Rake 42-531 22-11.00 x 8 Custom Smooth Tread Tire...
LUBRICATION Use No. 2 General purpose Lithium Base Grease and lubricate every 100 hours. The Diesel Super Rake has two grease fittings. One is located in bearing on steering shaft and the other is on the relay on the foot pedal.
Page 8
MAINTENANCE ENGINE OIL Change and add oil according to chart below. Do not overfill. Use a high quality detergent oil classified "For Ser- vice SJ or higher" SAE 30 oil. Use no special additives with recommended oils. Do not mix oil with gasoline. SAE Viscosity Grades Starting Temperature Range Anticipated Before Next Oil Change SAE 30 oil, if used below 40°...
Page 9
MAINTENANCE BATTERY Batteries normally produce explosive gases which can cause personal injury. Do not allow flames, sparks or any ignited object to come near the battery. When charging or working near battery, always shield your eyes and always provide proper ventilation. Battery cable should be disconnected before using "Fast Charge".
SERVICE CHART Before servicing or making adjustments to the machine, stop engine, set park break, block wheels and remove key from ignition. Follow all procedures and ONLY use parts prescribed by the manufacturer. Read the engine manual before maintenance. ¤ Engine Oil w/ Filter 3.28qt. (3.1 L) R R R ¤...
ADJUSTMENTS RAKE LIFT CYLINDER Completely lower Rake Lift. Remove cotter pin (A) and clevis pin (B). Place attachment lift arms (C) at " above cross member (D) on Rake Lift. Loosen jam nut (E). Twist cylinder extension (F) so clevis pin end of cylinder extension lines up with holes in attachment lift arm.
ADJUSTMENTS SPEED BOSS Speed Boss allows the machine to operate at a proper speed while raking bunkers on golf courses. This speed has been factory set at an average speed of 3-4 MPH(5-6.5 kph). The Speed Boss will only limit the speed while the rake is in lowered into the operating position.
WIRING DIAGRAM PARTS LIST REF# PART# DESCRIPTION QUANTITY Battery, 480 Cold Cranking Amps min. (not included) 22-054 Black Cable (negative) 76-236 Red Cable (positive) 12-031 Battery Boot (included with Red Cable) Starter (on engine) 14-272 Seat Switch 17-202 Temperature Gauge Temperature Sender (part of 17-202) Engine Oil Sensor...
ENGINE AND PUMP PARTS LIST REF# PART# DESCRIPTION QUANTITY 42-279 Mount 42-247 Creep Arm 8946-1.5 Wear Strip (part of 42-247) HRS-316-050 Rivet (part of 42-247) HMB-12-14 Machine Bushing x 14GA HP-18-100 Cotter Pin 42-311 Top Centering Arm 48-109 Spring 42-312 Bottom Centering Arm 18-168 Elbow...
13-729 2-BANK HYDRAULIC VALVE PARTS LIST REF# PART# DESCRIPTION QUANTITY 78-415-01 Body (complete with spacer and check valve) 78-415-02 Spool HDM10 78-415-03 O-Ring Seal 78-415-04 Flanged Washer HDM10 78-415-05 Spacer 78-415-06 A Type Spool HDS11 78-415-11 Positioner 78-415-08 Plug 78-415-09 Lever Group HDS11 78-415-10 Metric Socket Screw M5 x .8 x 45...
Page 45
13-032 FRONT WHEEL MOTOR (4.9 C.I.) PARTS LIST REF# PART# DESCRIPTION QUANTITY Water & Dirt Seal Service Housing Assembly Inner Seal 13-032-27 Thrust Bearing 13-032-28 Inner Bearing 13-032-29 Thrust Bearing 13-032-30 Drive Link Ring Seal 13-032-31 Manifold 13-032-32 Commulator Assembly (matched set) 13-032-33 End Cover...
Page 47
13-615 REAR WHEEL MOTOR (7.5 C.I.) PARTS LIST REF# PART# DESCRIPTION QUANTITY Water & Dirt Seal 13-615-05 Service Housing Assembly (Includes Ref 4, 5, 17(2 req'd) and 20) Inner Seal 13-032-27 Thrust Bearing 13-032-28 Inner Bearing 13-032-29 Thrust Bearing 13-615-03 Drive Link Ring Seal 13-032-31...
Page 49
LIFT ASSEMBLY PARTS LIST REF# PART# DESCRIPTION QUANTITY HCP-12-150 Clevis Pin HB-716-14-150 Bolt -14 x 1 13-004 Cooler Bracket Main Frame ( Part of Trap Rake HSSQ-38-16-200 Square Head Set Screw - 16 x 2 HN-38-16 - 16 HB-38-16-125 Bolt -16 x 1 HW-38 Washer...
13-680 HYDRAULIC PLOW WITH LIFT DRAWING (Dealer Installed) 13-679 HYDRAULIC PLOW WITH LIFT DRAWING (Factory Installed)
Page 53
INSTALLATION INSTRUCTIONS 1. Loosely bolt brace (Ref 2), to cylinder bracket (Ref 3) with the brace on top. The bolt and washer are on top; the washer and nut are on the bottom. 2. Remove two bolts that go through the bumper and bumper brace. Use these to bolt the cylinder bracket to the bumper. 3.
13-730 3-BANK HYDRAULIC VALVE PARTS LIST REF# PART# DESCRIPTION QUANTITY 78-416-01 Body (complete with spacer and check valve) 13-730-01 Spool HDM10 78-415-03 O-Ring Seal 78-415-04 Flanged Washer HDM10 78-415-05 Spacer 78-415-06 A Type Spool HDS11 78-415-11 Positioner 78-415-08 Plug 78-415-09 Lever Group HDS11 78-415-10 Metric Socket Screw M5 x .8 x 45...
Page 59
INSTALLATION INSTRUCTIONS 1. Disconnect the negative (-) ground battery cable from the battery. 2. Remove the four tapping screws holding the console cover to the console and remove the cover. 3. Remove the nuts from bolts (Ref 8). To hold the bolts you will have to go through the opening in the console.
13-107 SCARIFIER WITH CHISEL BLADES DRAWING To be used with 13-107 Scarifier with Chisel Blades and 13-577 Scarifier with Vertical Blades...
Page 63
13-107 SCARIFIER WITH CHISEL BLADES PARTS LIST To be used with 13-107 Scarifier with Chisel Blades and 13-577 Scarifier with Vertical Blades REF# PART# DESCRIPTION QUANTITY 13-117 Grader Blade HCP-12-150 Clevis Pin HHP-18 Bridge Pin 13-115 Hitch (Pistols) HMB-34-10 Machine Bushing x 10GA HMB-12-14 Machine Bushing...
Page 75
INSTALLATION INSTRUCTIONS 1.Attach drawbar (Ref 9) to hitch (Ref 11) using clevis pin (Ref 10) and cotter pin (Ref 12). 2. Attach rubber bumper (Ref 29) using cap nut and lock washer (Ref 21). Attach the rubber inserts (Ref 23) to the inside mounts (Ref 24 and 26).
Page 91
26-008 FLEX ACTION FIELD FINISHER PARTS LIST REF# PART# DESCRIPTION QUANTITY Rake Lift HCP-12-150 Clevis Pin HP-18-100 Cotter Pin HMB-12-14 Machine Bushing - 14GA HHP-18 Bridge Pin 26-046 Frame 26-049 Mounting Bar 26-047 Leveler Bar 21-060 Chain Clevis 26-115 Mesh Finisher HMB-58-14 Machine Bushing x 14GA...
Page 92
26-008 FLEX ACTION FIELD FINISHER DRAWING...
Page 93
INSTALLATION INSTRUCTIONS 1. Install flail bar strap (Ref 15) to center of mounting bar (Ref 7) with chain on top of flail bar strap and mounting bar bent away from you. Apply a light coat of lubricant to overall length of mounting bar. 2.
Speed Boss Hang Tag 25-352 Bypass Valve Hang Tag 25-354 Tire Pressure 5 psi All Three Wheels 25-357 Smithco Black Right and Left Nose Cone 25-361 Technical Assistance Main Frame 27-077 Smithco Round Steering Wheel 27-086 Left Side of Rear Cowling Below Seat (overseas machines only)
Batteries. Wheels and tires. A copy of the warranty for the above items is furnished if necessary with each SMITHCO product. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
Need help?
Do you have a question about the DIESEL SUPER RAKE and is the answer not in the manual?
Questions and answers