Download
Share
Print this page
Gage Bilt GB743SRVT Installation Tool Information
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Tools
  5. GB743SRVT
  6. Installation tool information

Gage Bilt GB743SRVT Installation Tool Information

Hide thumbs

Advertisement

Quick Links

Download this manual
S/N: 1070 AND ABOVE
GB743SRVT
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the GB743SRVT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Gage Bilt GB743SRVT

Summary of Contents for Gage Bilt GB743SRVT

  • Page 1 S/N: 1070 AND ABOVE GB743SRVT PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    Setting stroke - .900" (22.86 mm) Rated pull load - 4,000 lbs. (17.80 kN) Noise level - 81.5 dB (A) Vibration - Tested– No Hazards Found S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    81.5 dB (A). Therefore, daily basis for damage or wear. Any repair should it is required where prolonged use, hearing be done by qualified personnel trained on Gage Bilt protection be used. procedures. WARNING...

  • Page 4: Description, Maintenance And Hydraulic Thread Preparation

    7 1/4 lbs. (3.29kg) It has a .900” (22.86mm) rivet setting stroke. The GB743SRVT split handle riveter operates on a wide range of air pressure, with 90 to 100 psi. (6.2-6.9 bar) provid- ing maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB743SRVT does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles per minute.

  • Page 5: Filling & Bleeding

    With the lever ass’y released, check dimension (A). Holding lever ass’y check dimension (B). If stroke is not consistent within 1/64" (.0156) repeat bleeding steps 5-6. .226 (5.7mm) 1.126 (28.6mm) S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Troubleshooting

    Note: Offset nose assemblies must be check by removing the vacuum line from the nose assembly. b) Press gage against the vacuum line or nose assembly to create seal. Optimum vacuum pressure at nose assembly must be between 15-22 in.Hg S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 7: Overhaul, Disassembly And Parts List

    PERSONAL INJURY MAY OCCUR IF AIR HOSE IS NOT DISCONNECTED. USE CAUTION WHEN FORCING PISTON ROD ASSEMBLY DOWNWARD WITH HEAD CYLINDER ASSEMBLY REMOVED, HYDRAULIC OIL WILL EJECT FORCIBLY FROM HANDLE. S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 8 400066 SOCKET HEAD 400061 CAP SCREW (2) SOCKET HEAD CAP SCREW (2) 744303 - MANIFOLD-HANDLE S572 - STAT-O-SEAL (2) 402482 BUTTON HEAD CAP SCREW (2) S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 9 744142 - VALVE PLUG 400785 - O'RING 744136 744143 - MUFFLER PISTON ROD ASSEMBLY 744124 - BASE COVER (INCLUDES S908 AND A-201) 744149 - PIN S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 10: Dexron® Iii Oil Safety Data

    PROPERTIES Specific Gravity 0.863 Weight per gallon 7.18 ° °F) Open flash point >200 C (392 S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 11: Nose Assembly Selection Chart

    S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 12 S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 13: Eu Conformity And Warranty

    DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING CO. LOCTITE® IS A REGIS- TERED TRADEMARK OF HENKEL CORPORATION. S/N: 1070 AND ABOVE REV. 7/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.