Related Manuals for Gerima SMA 20 AEF-24.K1
Summary of Contents for Gerima SMA 20 AEF-24.K1
- Page 1 © Operating manual Hand-held beveling machine SMA 20 AEF-24.K1 SMA 20 AEF-14.K1 Operating manual...
-
Page 2: Preface
All rights, including translation, are reserved. No part of this manual may be reproduced in any form (print, photocopy, microfilm or any other process) without the written permission of GERIMA GmbH, St. Wendel, reproduced or distributed using electronic systems, duplicated or distributed. -
Page 3: Table Of Contents
© Directory Preface…….…………………………………………. Imprint…...………………………………………….… 2 Foreword……………………………………………... Signs and symbols ..……………………………….. Technical specification………………….………… 6 Technical data….…………………………………….. 6 Shipment….………………………….……………….. 6 Noise emission value…..………………………….… 7 Power-on time…………..………………………….… 7 Safety instructions……….………………………… 8 Basic safety instructions…………….………………. 8 Intended use………………………...……………….. 13 Settings………………...……………………..……… 14 Replacing guiding roll……………...………………... 14 Replacing carbide inserts…………………………... -
Page 4: Foreword
Should you need to contact us for assistance, GERIMA machine. please always have the identification number of your GERIMA SMA 20 AEF-24.K1 / SMA 20 AEF- 14.K1 available. The machine identification number is engraved on the gear box (see red arrow in diagram shown at top right of page). -
Page 5: Signs And Symbols
© Signs and symbols Please read the manual before using the ma- The information in this manual are indentified chine ! as follows: This manual has been created so that you can Danger! work with your device quickly and safely. Here is a Warning of person, machinery or brief guide on how you should read this manual: environmental damage. -
Page 6: Technical Specification
Main scale Motor Milling head with guiding roll Height clamping lever Spindle lock On-/Off-switch Guiding plate Vernier scale Shipment 1x Basic machine SMA 20 AEF-24.K1 SMA 20 AEF-14.K1 with milling head 1x Manual 1x Torx wrench T15 1x Screwdriver SW4... -
Page 7: Noise Emission Value
© Technical manual Noise emission values in accordance with the DIN Power-on time (POT): EN 60745-1 standard: To avoid damaging the machine, it is essential to be monitor how long the machine has been Noise emission [dB (A)] Value operating continuously (‘power-on time’). certainty Emission sound pressure All electric brushed motors generate large amounts... -
Page 8: Safety Instructions
• this staff must be instructed regularly about rele- vant occupational safety and environmental pro- • Always use genuine GERIMA spare parts and tection and know the operating instructions and accessories or those that have been approved for the safety instructions. - Page 9 © Basic safety instructions Operator qualifications and protection of ma- Protective clothing: chine operators: When working on/with the machine always wear: The term ‘operator’ is used here to mean any per- son who operates, adjusts, services and/or repairs the machine. The employer is obliged to inform the operator ear protectors, about security relevant standards and to verify...
- Page 10 Do not lay the cable over manufacturer’s service personnel. sharp edges. • Always use genuine GERIMA spare parts and • Repair: The machine may only be repaired by accessories. appropriately qualified technical staff or by the manufacturer’s service personnel.
- Page 11 © Basic safety instructions Risk of electric shock! Regular pre-start safety precautions Warning of physical injury by electricity Perform the following pre-start proce- dures each time you plan to use the • All work on the machine’s electrical machine: systems must be performed only by qualified •...
- Page 12 When performing any servicing, maintenance Any alterations to the machine must or repair work de-energize the machine by dis- have been approved by GERIMA connecting it from the supply and ensure that GmbH. the machine cannot be switched on again ac- This also applies to the welding of cidentally.
-
Page 13: Intended Use
© Basic safety instructions / Intended use Cleaning the machine and disposal information: The hand-held beveling machine SMA 20 AEF- 24.K1 / 14.K1 may only be used for work and ma- All substances and materials used terials described in the section ‚intended use‘. must be handled appropriately and accordance with all relevant statuto- Do not use the machine to work on... -
Page 14: Settings
© Settings Replacing guiding roll / carbide inserts Adjusting the 4-fold insert type MV and the 8 bevel and radius inserts (type SX and RSX): Before replacing always disconnect the The bevel and radius carbide inserts of type SX and RSX machine from the power supply by re- each have 8 cutting edges. -
Page 15: Setting The Bevel Length
© Settings Setting the bevel length: Adjusting radius: The procedure for setting the radius and bevel is identi- a leg length = bevel length a cally. Please note that only the position of the upper b leg length = bevel length b edge of the radius can be adjusted by rotating the guid- C bevel width ing plate. -
Page 16: Operating Mode
© Operating mode General: Handling: Two-handed operation: Damages caused by wrong power supply! Whatever the position of the • Check the supply voltage. The supply machine, always use two hands to control the machine. voltage must correspondend with the specifications on the type plate of the machine. -
Page 17: Maintenance
! • Wear protective gloves when changing or readjusting the carbide inserts! Repair must only be carried out by a GERIMA trained technician! Improperly repaired machines are hazzard! • Increased risk of injury • Machine does not function correctly! Hot carbide inserts and milling head! •... -
Page 18: Technical Documentation
© Technical documentation Assembly group SMA 20 AEF-24.K1 / -14.K1 0202-20-00-00-00-06 name of part order-nr. Spindle with milling head 45° 0101.112.19-00010 Distance disc 0101.112.19-00011 Bevel gear 0101.112.19-00009 Handle 0101.112.15-00015 Distance-ring 0101.112.15-00016 Distance-ring 0101.112.15-00017 Steel bush 0101.112.15-00006 Counter-ring 0101.112.15-00005 Guiding plate 0101.112.15-00004... -
Page 19: Terms Of Guarantee
GERIMA or by one of its authorized specialist retailer or representatives. Guarantee claims can be made only for genuine GERIMA parts and if the machine was used for its intended purpose. The guarantee does not cover, in particular: operational wear and tear; improper use;... -
Page 20: Ec Declaration Of Conformity
Weimarer Straße 12 66606 St. Wendel Germany Product SMA 20 AEF-24.K1, 21-240-*****, 00001-99999, 2021 Product SMA 20 AEF-14.K1, 21-241-*****, 00001-99999, 2021 We hereby declare that the above mentioned product complies with all relevant provisions of the Machinery Directive 2006/42/EC. The above product fulfills the relevant requirements of the following guidelines: ►...