Related Manuals for Fein ABLK 1.3E/TSE
Summary of Contents for Fein ABLK 1.3E/TSE
- Page 1 Repair instructions FRT: A BLK 1.3 TE/CSE, 1.6 E ABLK 1.3E/TSE, 1.6E All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 1/33 FEIN retains all rights of disposal, such as copying and circulation.
-
Page 2: Table Of Contents
Technical data Provisions Tools required Lubricants and auxiliary substances required Disassembly Assembly Connection diagram All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 2/33 FEIN retains all rights of disposal, such as copying and circulation. -
Page 3: Models Described
Order no. ABLK 1.3 TE 713203 ABLK 1.3 CSE 713202 ABLK 1.6 E 713201 All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 3/33 FEIN retains all rights of disposal, such as copying and circulation. -
Page 4: Technical Data
The complete technical data can be found in the operating instructions for the model. Test data Up-to-date test data for all models can be found on the FEIN Extranet (Customer Service → Repair Guides). Lubricants Lubricants and container sizes available from FEIN can be found on the FEIN Extranet (Customer Service →... -
Page 5: Provisions
The German Equipment and Product Safety Act applies for correct use. Outside Germany, the regulations applicable in the relevant country must be observed! All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 5/33 FEIN retains all rights of disposal, such as copying and circulation. -
Page 6: Tools Required
Circlip pliers Punch Arbor press Cable hooks Slide gauge Feeler gauge Hot air gun All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 6/33 FEIN retains all rights of disposal, such as copying and circulation. -
Page 7: Lubricants And Auxiliary Substances Required
Sliding surfaces of plunger, con rod, punch Auxiliary substances Loctite 574 Between gearbox head and intermediate bearing All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 7/33 FEIN retains all rights of disposal, such as copying and circulation. - Page 8 FRT: A BLK 1.3 TE/CSE, 1.6 E Disassembly - Preparation 1. Press releasing button and pull out battery. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 8/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 9 Torx 15 3. Remove upper section of housing. 4. Remove control rod. 5. Remove electronics from lower section of housing together with motor and gearbox head. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 9/33...
- Page 10 Disassembly - Motor 1. Pull off motor plug on electronics. 2. Take off rubber ring. 3. Remove protective grille. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 10/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 11 6 41 14 033 00 0 -Hot air gun NOTE Heat intermediate bearing before separating from motor. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 11/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 12 6.2. 1. Pull intermediate bearing off gearbox head. 2. Remove intermediate gear shaft. 3. Remove sealing ring from intermediate bearing. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 12/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 13 26 mm 6 41 07 026 00 0 -Drawing-off socket cap 6 41 04 150 00 8 All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 13/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 14 The motor is only available as a spare part together with the intermediate bearing. The intermediate bearing is only available as a spare part together with pressed-in bearing bush and pressed-in ball bearing. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 14/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 15 1. Remove circlip, gear-wheel and feather key. - Plastic hammer 2. Remove circlip and drive eccentric shaft and drive out of gearbox housing by tapping gently with hammer. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 15/33...
-
Page 16: Disassembly
1. Remove retainer nut with open-ended spanner (WAF 30). 2. Carefully remove plunger from gearbox housing. Tool: - Open-ended spanner, WAF 30 All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 16/33 FEIN retains all rights of disposal, such as copying and circulation. - Page 17 1. Loosen retainer nut and remove cutting head with punch and plunger. 2. Remove plunger and punch from cutting head. Tool: - Screwdriver - Punch All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 17/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 18 2. Take punch out of cutting head and remove from lower section of plunger. Tool: -Open-ended spanner WAF 30 All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 18/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 19 A BLK 1.3 TE/CSE, 1.6 E 6.6. Disassembly - Cutting head (ABLK 1.6E) 1. Remove screw (with O-ring). 2. Remove die from cutting head. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 19/33 FEIN retains all rights of disposal, such as copying and circulation.
-
Page 20: Assembly
Repair instructions FRT: A BLK 1.3 TE/CSE, 1.6 E 7. Assembly All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 20/33 FEIN retains all rights of disposal, such as copying and circulation. - Page 21 Grease: 4.Coat sliding surface between punch and die with Molykote paste. - Tube 85g 3 21 60 003 19 8 All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 21/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 22 7.1. Assembly - Die and plunger / gearbox housing (ABLK 1.3 TE/CSE) 1. Insert fully assembled die into gearbox housing. 2. Fix die in place with retainer nut. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 22/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 23 Tool: 2. Slide retainer nut over cutting head and screw down to gearbox housing. - Open-ended spanner WAF 30 All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 23/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 24 !!! Only fits in one position !!! 2. Fit screw (with O-ring) in cutting head. Tool: -Socket wrench 6 mm All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 24/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 25 (Eccentric shaft must engage in drive) - Straight long-nosed pliers 3. Fit circlip. - Circlip pliers All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 25/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 26 - Flat nose pliers 2. Insert disc. - Circlip pliers 3. Fit intermediate gear shaft. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 26/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 27 Dimensions are shown in the drawing on the next page. - Feeler gauge - Press-in fixture 6 41 22 108 00 0 All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 27/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 28 Repair instructions FRT: A BLK 1.3 TE/CSE, 1.6 E 7.5. Assembly – Motor / intermediate bearing All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 28/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 29 FRT: A BLK 1.3 TE/CSE, 1.6 E 7.6. Assembly – Motor 1. Connect motor cable on electronics. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 29/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 30 7.6. Assembly – Motor 1. Check dimensional accuracy of rubber ring on motor. Tool: - Slide gauge All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 30/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 31 2. Insert control rod. Tool: Ensure that control rod is under spring. - Cable hooks All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 31/33 FEIN retains all rights of disposal, such as copying and circulation.
- Page 32 5. Fit holding down device. -Torx 15 screwdriver -Loctite 574 6. Perform function check. All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 32/33 FEIN retains all rights of disposal, such as copying and circulation.
-
Page 33: Connection Diagram
Repair instructions FRT: A BLK 1.3 TE/CSE, 1.6 E Connection diagram Motor Electronics Plug All rights reserved by FEIN, especially in case of industrial rights registration. C-SC_CSSM 2012.07 33/33 FEIN retains all rights of disposal, such as copying and circulation.