Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for OREC SF600
- Page 1 ROTO-TILLER SF600 / SF600D Read this instruction manual carefully before any use of the machine, keep it as a reference. For any question about this manual, please report to your OREC dealer or to the distributor of your country or to: http://www.orec-jp.com.
-
Page 2: Introduction
Use only the OREC original parts : “ non genuine ” parts will not assure you of a correct and safe working and are likely to make the guarantee null and void. Write the name and the serial number of your machine hereunder : MODEL :.................. -
Page 3: Table Of Contents
INSTRUCTIONS TO THE DEALER • The assembling, the installation and the first application of the machine is under the OREC dealer’s responsibility. • Read the instruction manual as well as the safety measures. Check that all the before delivery and at delivery check points specified in the following lists have been verified and possibly modified before delivering the machine to its owner. -
Page 4: Safety Rules
• Always use a chuck and bronze hammer when replacing or intervening on the pins and bolts at the end of rams, rod … etc in order to avoid the projection of metal fragments. OREC SF600/600D... -
Page 5: Different Parts Of The Machine
Throttle Speed lever and tool inversion lever Diff lock lever Starter Handle adjustment Air filter Exhaust silence Counter wheight Fuel Tank Figure 1 Travel&Clutch lever Speed lever and tool inversion lever Working depth adjustment Rotary Cover Figure 2 OREC SF600/600D... -
Page 6: Safety Instruction Stickers
SAFETY INSTRUCTION STICKERS Note their location and replace them immediately in case of damage or when missing -Read owner's manual -Beware of Flammable gasoline -Beware of exhaust gases -Beware of hot surfaces near the engine Beware of rotating belt under the shield Do not exceed 15°... -
Page 7: Controls
Figure 4-2 WARNING Release the travel lever to change of speed. When the speed is engaged, open the throttle slowly. DANGER Take many care when travelling on reverse to not stumble on bumps, holes or debris on the ground. OREC SF600/600D... - Page 8 When the switch is on "stop" the engine is stopped and cannot be started. Put the switch on "stop" position to stop the engine or to avoid starting. • Place the switch to the "on" position to allowed the engine to start. Figure 9 OREC SF600/600D...
- Page 9 To adjust the handlebar : • Unscrew the knob at the low side of the handlebar. • Pull of the axle with Jack bolt(A, Figure 11). • Adjust the handlebar as required • Put the axle, and screw the knob. Figure 11 OREC SF600/600D...
- Page 10 Stop the engine and disconnect the spark plug before clean or perform any maintenance on the machine. Do not push the rot tiller when the toll is rotating, it may damage the transmission Working on a soft ground(SF600)(Figure 12-1) •...
- Page 11 Remove sparking ignition wire from the sparking plug. • Remove rust and paint the metal. • Store the machine in a dry protected area. RANSPORTATION disconnect the spark plug . close the fuel cock. Fix the machine with rope securely. OREC SF600/600D...
-
Page 12: Maintenance Operations To Be Carried Out By The User
Check tires pressure : 1,2 bar. Safety stickers Check safety stickers are sticked at their place. Replace them if they are worn and damage. State of the working tool blade(SF600)(figure 15-1) CAUTION Blades can cut hands or fingers; always wear protective gloves when holding blades. - Page 13 CAUTION Foam Only use original genuine OREC parts. Other parts may be dangerous for your health and for the bystanders and the machine. If some vibration occur. If you feel vibrations in the handlebar, check the blade. Vibrations may cause loosening of the bolt and nuts and may crack the steel of the machine.
- Page 14 Lubricate with light oil (engine oil) following points : • Wires and control lever axles (A & B, Figure 19). • Stand (A, Figure 20-1(SF600), 20-2(SF600D)). • On the gear box, the diff lock lever and the speed lever. •...
-
Page 15: Breakdowns And Solutions
Cannot use because of clay or ground is too hard. Turn the soil by other machine in advance. Cannot cultivate Dashing of the machine Easy Anchor is worn or dropped. Cultivate too deep Cannot cultivate completely Change all tine for new one. Easy Anchor is worn OREC SF600/600D... -
Page 16: Tightening Torques (Kgf.cm)(Sf600)
TIGHTENING TORQUES (Kgf.cm)(SF600) Marks on the headscrew DIAMETER OF THE SCREW or without mark (mm) 0,3 to 0,5 0,8 to 1,0 2,5 to 3,4 5,4 to 6,4 6,4 to 7,4 6,4 to 7,4 8,8 to 9,8 4,9 to 6,9 9,8 to 11,8... -
Page 17: Ec Conformity Declaration
EC CONFORMITY DECLARATION Business name and full address of the manufacturer : OREC CO LTD 548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN FUKUOKA JAPAN S.A.T. sarl - Force 7 – ZA – 38110 ROCHETOIRIN France owner of the technical documents Designation : rototiller... -
Page 18: Ec Conformity Declaration
EC CONFORMITY DECLARATION Business name and full address of the manufacturer : OREC CO LTD 548-22 HIYOSHI HIROKAWA-MACHI YAME-GUN FUKUOKA JAPAN S.A.T. sarl - Force 7 – ZA – 38110 ROCHETOIRIN France owner of the technical documents Designation : rototiller... -
Page 19: Limited Warranty
The guarantee is limited to the parts that are previously shown to and acknowledged by OREC. 2° Each part concerned by a guarantee claim must be returned to OREC’s in order to be inspected, repaired or replaced.