SG Models MAXI LIFT 33cc Assembly Manual
  1. Manuals
  2. Brands
  3. SG Models Manuals
  4. Toy
  5. MAXI LIFT 33cc
  6. Assembly manual

SG Models MAXI LIFT 33cc Assembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual.
A S S E M B L Y M A N U A L
MAXI LIFT
33cc
Code: SEA209
" Graphics and specifications may change without notice " .
Specifications:
Wingspan---------------87.6 in (222.2 cm).
Wing area----------------1072.6sq.in (69.2 sq.dm).
Weight-------------------11.5 - 12.1 lbs (5.2 - 5.5 kg).
Length-------------------61.2 in (155.5cm).
Recommended engine size 33cc...............................
Radio--------------------7 channels with 10 servos.
Flying skill level intermediate/ advanced
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MAXI LIFT 33cc and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SG Models MAXI LIFT 33cc

Summary of Contents for SG Models MAXI LIFT 33cc

  • Page 1 Instruction Manual. A S S E M B L Y M A N U A L MAXI LIFT 33cc Code: SEA209 “ Graphics and specifications may change without notice “ . Specifications: Wingspan---------------87.6 in (222.2 cm). Wing area----------------1072.6sq.in (69.2 sq.dm). Weight-------------------11.5 - 12.1 lbs (5.2 - 5.5 kg).

  • Page 2: Kit Contents

    MAXI LIFT INTRODUCTION. Thank you for choosing the MAXI LIFT ARF by SG MODELS . The MAXI LIFT was de- signed with the intermediate/advanced sport flyer in mind. It is a semi scale airplane which is easy to fly and quick to assemble. The airframe is conventionally built using balsa, plywood to make it stronger than the average ARF, yet the design allows the aeroplane to be kept light.

  • Page 3: Additional Items Required

    Instruction Manual. KIT CONTENTS. HINGING THE FLAP SEA20901 Fuselage SEA20902 Wing Set SEA20903 Tail Set SEA20904 Fiberglass Cowling SEA20905 Canopy SEA20906 Landing Gear SEA20907 Wheels SEA20908 Wing struts SEA20909 Pilot ADDITIONAL ITEMS REQUIRED. M2x10 mm 0.75- 0.91 2-stroke. 0.91-1.25 4-stroke. 33cc gasoline engine.

  • Page 4: Hinging The Elevator

    MAXI LIFT NOTE : The hinge is constructed of a spe- HINGING THE ELEVATOR. cial material that allows the C/A to wick Note : The control surfaces, including the ai- or penetrate and distribute throughout lerons, elevators, and rudder, are prehinged the hinge, securely bonding it to the wood structure of the wing panel and aileron.

  • Page 5: Hinging The Rudder

    Instruction Manual. 7) Repeat this process with the other wing panel, securely hinging the aileron in place. 8) After both ailerons are securely hinged, firmly grasp the wing panel and aileron to make sure the hinges are securely glued and cannot be pulled out.

  • Page 6: Installing The Main Landing Gear

    MAXI LIFT INSTALL RUDDER CONTROL HORN. Repeat steps to install the rudder control horn as same as steps done for ailerons. Epoxy Aileron control horn. INSTALL ELEVATOR CONTROL HORN. Epoxy Fiberglass control horn. Epoxy Rudder control horn. Epoxy INSTALLING THE MAIN LANDING GEAR.

  • Page 7: Installing The Fuselage Servos

    Instruction Manual. Collar. 4x20 mm INSTALLING THE FUSELAGE SERVOS. Because the size of servos differ, you may need to adjust the size of the precut opening in the mount. The notch in the sides of the mount allow the servo lead to pass through. 1) Install the rubber grommets and brass collets onto the throttle servo.

  • Page 8: Installing The Switch

    MAXI LIFT INSTALLING THE SWITCH. Install the switch into the precut hole in the side, in the fuselage. 3/32” Hole. Elevator servo arm. Trim and cut Rudder servo. Switch for engine. Servo tow. Servo capping. Trim and cut...

  • Page 9: Mounting The Engine

    Instruction Manual. 5) Slide the pushrod tube in the firewall and guide it through the fuel tank mount. Use medium C/A to glue the tube to the firewall and the fuel tank mount. 6) Connect the Z-bend in the 600mm throt- tle pushrod to the outer hole of the carbure- tor arm.

  • Page 10: Installing The Stopper Assembly

    MAXI LIFT THROTTLE SERVO ARM INSTALLATION. Install adjustable servo connector in the servo arm as same as picture below: Adjustable Servo Loctite secure. connector. Servo arm. 1 PCS INSTALLING THE STOPPER ASSEMBLY. 1) Using a modeling knife, carefully cut off the rear portion of one of the 3 nylon tubes leaving 1/2”...

  • Page 11: Fuel Tank Installation

    Instruction Manual. 5) With the stopper assembly in place, the weighted pick-up should rest away from the rear of the tank and move freely inside the tank. The top of the vent tube should rest just below the top of the tank. It should not touch the top of the tank.
  • Page 12 MAXI LIFT Vent tube. Fuel pick up tube. Fuel fill tube. 9) Connect the lines from the tank to the en- gine and muffler. The vent line will connect to the muffler and the line from the clunk to the carburetor. Blow through one of the lines to ensure the fuel lines have not become kinked inside the fuel tank compartment.

  • Page 13: Installing The Spinner

    Instruction Manual. INSTALLING THE SPINNER. Install the spinner backplate, propeller and spinner cone. 2) While keeping the back edge of the cowl flush with the marks, align the front of the cowl with the crankshaft of the engine. The front of the cowl should be positioned so the crankshaft is in nearly the middle of the cowl opening.
  • Page 14 MAXI LIFT 1) Using a small weight (Weighted fuel pick- up works well) and string, feed the string through the wing as indicated. 2) Place the servo between the mounting 6) Secure the servo to the aileron hatch using blocks and space it from the hatch. Use a Phillips screwdriver and the screws provided pencil to mark the mounting hole locations with the servo.
  • Page 15 Instruction Manual. AILERON PUSHROD NSTALLATION. 100mm. M3 clevis. M3 lock nut. Wing 9) Set the aileron hatch in place and use a Phillips screw driver to install it with four INSTALLING THE FLAP SERVO. wood screws. Repeat the procedure for the aileron servo.
  • Page 16 MAXI LIFT 90mm. M3 clevis. M3 lock nut. Wing INSTALLING TOW RELEASE FOR SAIL PLANE. It is best to operate the aero-tow release mechanism using a momentary switch Screw the aero-tow mechanism into the mounted on the joystick. The servo travel hole just behind the canopy, and apply must be set accordingly.

  • Page 17: Installing The Horizontal Stabilizer

    Instruction Manual. INSTALLING THE HORIZONTAL STABILIZER.
  • Page 18 MAXI LIFT 1) Using a ruler and a pen, locate the center- line of the horizontal stabilizer, at the trail- Remove the covering. ing edge, and place a mark. Use a triangle and extend this mark, from back to front, across the top of the stabilizer.
  • Page 19 Instruction Manual. 3) While holding the vertical stabilizer firm- ly in place, use a pen and draw a line on each side of the vertical stabilizer where it meets the top of the fuselage. INSTALLING VERTICAL FIN. 4) Remove the stabilizer. Using a modeling knife, remove the covering from below the lines you drew.

  • Page 20: Elevator Pushrod Installation

    MAXI LIFT 6) When you are sure that everything is aligned correctly, mix up a generous amount of Flash 30 Minute Epoxy. Apply a thin lay- er to the mounting slot and to bottom of the vertical stabilizer mounting area. Ap- ply epoxy to the bottom and top edges of the filler block and to the lower hinge also.
  • Page 21 Instruction Manual. M3 clevis. Crimp. Metal connector. Cable end. 810mm. 810mm. 185 mm THE TAIL WHEEL - STRUT SUPPORT. M2 clevis. M2 clevis. M2 lock nut. M2 lock nut. Locate items necessary to install tail wheel. Bend at the mark. Aluminum tail landing gear.
  • Page 22 MAXI LIFT Bend at the mark. Metal clevis. Fuel tubing. Hex nut. INSTALLING TAIL STRUT SUPPORT. The tail strut system assembly follow pic- tures below. Fuel tubing. Hex nut. 810mm. 810mm. 280mm Metal clevis. M2 clevis. M2 clevis. M2 lock nut. M2 lock nut.
  • Page 23 Instruction Manual. Epoxy. INSTALLATION PILOT AND CANOPY. 1) Locate items necessary to install pilot and canopy. Epoxy. 2) A scale pilot is included with this ARF. The Pilot included fitting well to the cockpit. (or you can order others scale pilot figures made by SG-Models.They are available at SG-Models distributors.) If you are going to install a pilot figure,...

  • Page 24: Apply The Decals

    MAXI LIFT Attach the aluminium tube into fuselage. APPLY THE DECALS. 1) If all the decals are precut and ready to Wing tube. stick. Please be certain the model is clean and free from oily fingerprints and dust. Position decal on the model where desired, using the photos on the box and aid in their location.
  • Page 25 Instruction Manual. Wing bolt. M3x25mm Wing. INSTALLATION WING- FUSELAGE STRUTS. M3x25mm Fuselage. Wing. Wing.

  • Page 26: Control Throws

    MAXI LIFT With the wing attached to the fuse- lage, all parts of the model installed ( ready to fly), and empty fuel tanks, hold the model at the marked bal- ance point with the stabilizer level. Lift the model. If the tail drops when you lift, the model is “tail heavy”...

  • Page 27: Flight Preparation

    Instruction Manual. FLIGHT PREPARATION. PREFLIGHT CHECK. Check the operation and direction of the 1) Completely charge your transmitter and elevator, rudder, ailerons and throttle. receiver batteries before your first day of flying. A) Plug in your radio system per the 2) Check every bolt and every glue joint in manufacturer’s instructions and turn eve- the MAXI LIFT to ensure that everything is...

This manual is also suitable for:

Sea209

Table of Contents