Coffee Delivery; Beverage Selection - DeLonghi EC9335.M Manual

The first time you use the appliance, we recommend using the
factory setting (medium grinding) (fig. 14), then if you are not
satisfied with the result, adjust the level according to your per-
sonal taste and the type of coffee by setting a finer or coarser
grinding level, referring to the tips in section "4.5 Adjusting the
quantity of ground coffee in the filter".
Important:
• Always adjust the coffee mill while in operation.
• Adjust one grinding level at a time and make at least 5 coffees
before adjusting again.
• Do not remove the beans container while it contains beans.
4.3 The coffee filters
The appliance is provided with two coffee filters.
The 1 coffee filter (C2) has the
bottom.
The 2 coffee filter (C3) has the
bottom.
For the correct quantity of coffee, the ideal level of pressed coffee
is marked inside the filters (fig. 16). If the quantity is above or
below the level indicated, the result may not be satisfactory. The
next times you use the coffee mill, you can adjust the grinding
level using the dial (B2) (see section "4.5 Adjusting the quantity
of ground coffee in the filter").
4.4 Grind the coffee directly into the filter
1. Place the ground coffee filter (C2) or (C3) in the filter holder
(C1) (fig. 17);
2. Press the "X2" button if you are using the 2 coffee filter;
3. Attach the filter holder to the outlet of the coffee mill
(A22), aligning it with
18). Grinding begins when the filter holder reaches the
position and stops automatically;
Important: while the appliance is grinding coffee, you can per-
form a rinse, or produce hot water or steam at the same time.
4. Once grinding is complete, the
the presser lever (A23) as far as it will go. The force exerted
on the coffee is indicated on the lever itself (
(fig. 19). The light remains on steadily.
5. Remove the filter holder by turning it towards the left.
Important: to adjust the correct quantity ground automatically into the filter hold-
er, see section "4.5 Adjusting the quantity of ground coffee in the filter".
If you remove the filter holder from the outlet of the coffee mill
without pressing the coffee, the
press, turn the dial (B2) to the
mill, re-attach the filter holder and pull the lever (A23).
4.5 Adjusting the quantity of ground coffee in
the filter
Important: The first time you use the coffee mill, leave the dial
in the position (min). It is normal for you to have to grind the
symbol marked on the
symbol marked on the
, then turning it to the right (fig.
light (B16) flashes. Pull
light (B16) flashes. To
position to disable the coffee
coffee a number of times before finding the correct adjustment for
the right amount of coffee.
Perfect dose
After grinding coffee for the first time, turn the dial (B2) gradu-
ally, starting from the
until you reach the correct quantity, depending on the type of
coffee. The ideal position is within the sector shown in grey in
the following figure.
By adjusting this dial, you can adapt the mill to any type of coffee
and to wear of the burrs over time.

5. COFFEE DELIVERY

)

5.1 Beverage selection

1. Turn the mode selector dial (B8) to select the desired coffee
(see section "5.4 Coffee beverages").
2. If you use the 2 cup filter (C3), press the "2X" button (B3).
5.2 Delivering the coffee
1. Attach the filter holder (C1) to the appliance. To attach
correctly, align the filter holder handle with
then turn the handle to the right until it is aligned in the
position;
2. Place the cup or cups under the filter holder spouts;
3. If you are using small cups, lower the cup grille (A10) to
bring the filter holder spouts nearer the cup. This makes a
better froth (fig. 20);
30
Too much coffee Too little coffee
"min" position (see following figure)
(fig. 10),