Sealey Premier CST989HD Quick Start Manual

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear safety
instructions footwear
1. Safety
Always load evenly with the centre of gravity of the load as near the centre and rear of the plate as possible.
9
obtain additional support for large or wide loads to prevent tipping.
9
Do not overload the truck - see Specification.
8
Do not leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.
8
Do not use truck on uneven ground and do not run over curbs or steps - use a ramp.
8
Do not allow others to ride on the truck.
8
Do not use the truck if any part is damaged, paying particular attention to the wheels.
8
2. introDuction
Heavy-duty tubular steel construction with welded joints with 300kg capacity. Puncture proof heavy-
duty PU tyres with powder coated steel hubs. Features foldaway toe plate for added extension when
transporting larger loads. Can be used as a traditional sack truck or at a 45° with support castors. Three
year warranty.
3. SPecification
Model no: ............................................CST989Hd
Capacity: ...................................................... 300kg
Height(s): ................................................. 1220mm
nett Weight: ................................................ 19.1kg
overall Width: ............................................ 600mm
Platform depth: .......................................... 300mm
Wheel Bore Size: ...................................... Ø20mm
Wheel Size: ............................................. Ø250mm
Wheel Width:................................................ 85mm
4. aSSeMbly
4.1. attacHing tHe wHeelS
4.1.1. Make sure the axle is free from dust and dirt to allow free rotation of the wheel.
4.1.2. Place spacer (Fig.1.2) onto axle first. Slide the wheel (Fig.1.3) onto the axle
followed by a washer (Fig.1.4). Push a split pin (Fig.1.5) through the hole in the end
of the axle and bend over the ends in order to secure the whole assembly.
4.1.3. Push axle through fame, repeat for the other side.
4.1.4. The truck can be used in three different configurations as shown in Figs. 2, 3 & 4.
4.2. StanDarD Sack truck. To operate as a two wheel sack truck ensure that the
castor wheels and secondary frames are secured flat against the main frame. The
castor wheels should be turned sideways and the loop handle should be resting in the
lower stowage bracket with the locking pin in place, as shown in Fig.2.
4.3. Sack truck SuPPorteD at 45°. To use as a 45° sack truck release the
secondary frame and wheels by removing the locking pin from the lower bracket. Take
hold of the loop handle with one hand and tip the truck towards you with the other hand
until the loop handle can be placed into the upper bracket and secured with the locking
pin, as shown in Fig.3.
4.4. flat beD truck. To use as a flat bed truck release the secondary frame
and castor wheels by removing the locking pin from the securing bracket. Take
hold of the loop handle and tip it towards you so that it clears the square tube at
the top of the main frame between the red handles. With the other hand lower
the main frame until the square tube comes to rest on the slotted bracket about
12cm above the castor wheels, as shown in Fig.4. Fold up the load restraint at
the other end of the frame until it rests against the platform. Manoeuvre the
loaded trolley using the loop handle only. Do not lift the truck by the red
handles when used in flat bed configuration.
warning! When changing truck positions keep fingers well clear of all pinch points.
‰
© Jack Sealey limited
Heavy-Duty 3-in-1 Sack truck witH Pu
tyreS 300kg caPacity
cSt989HD
Model no:
fig.1
Original Language Version
fig.2
fig.4
CST989Hd Issue 1 16/05/19
fig.3