Sealey CST989.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
Always load evenly with the centre of gravity of the load as near the centre and rear of the plate as possible.
9
Obtain additional support for large or wide loads to prevent tipping.
9
DO NOT overload the truck - see Specification.
8
DO NOT leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.
8
DO NOT use truck on uneven ground and DO NOT run over curbs or steps - use a ramp.
8
DO NOT allow others to ride on the truck.
8
DO NOT use the truck if any part is damaged, paying particular attention to the wheels.
8
2. INTRODUCTION
Tubular steel framework with heavy-duty pneumatic tyres allows transport of load over rough
terrain. Suitable for use as a traditional sack truck or at 45° with support castors in position. For
maximum load carrying capability use in horizontal position. Features fold out load restrainer
for use when truck is in horizontal position. Adapts between configurations in seconds.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . CST898.V3
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250kg
Height(s): . . . . . . . . . . . . . . . . . . . . . . . . . . . .1275mm
Overall Width: . . . . . . . . . . . . . . . . . . . . . . . . .600mm
Platform Depth: . . . . . . . . . . . . . . . . . . . . 600/620mm
Wheel Size: . . . . . . . . . . . . . . . . . . . . . . . . Ø250mm
Wheel Width: . . . . . . . . . . . . . . . . . . . . . . . . . . .90mm
Nett Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19kg
4. ASSEMBLY
4.1. Make sure the axle is free from dust and dirt to allow free rotation of the wheel.
4.2. Place spacer (fig.1.2) onto axle first. Slide the wheel (fig.1.3) onto the axle (fig.1.1)
followed by a washer (fig.1.4). Push a split pin (fig.1.5) through the hole in the end of the
axle and bend over the ends in order to secure the whole assembly.
4.3.
Push axle through fame, repeat for the other side.
5. OPERATION
5.1. The truck can be used in three different configurations as shown in (figs.2.3 & 4).
5.2. Standard Sack Truck. To operate as a two wheel sack truck ensure that the castor
wheels and secondary frames are secured flat against the main frame. The castor
wheels should be turned sideways and the loop handle should be resting in the lower
stowage bracket with the locking pin in place, as shown in (fig.2).
5.3. Sack Truck supported at 45°. To use as a 45° sack truck release the secondary frame
and wheels by removing the locking pin from the lower bracket. Take hold of the
loop handle with one hand and tip the truck towards you with the other hand until the
loop handle can be placed into the upper bracket and secured with the locking pin, as
shown in (fig.3).
5.4. Flat bed truck. To use as a flat bed truck release the secondary frame and castor
wheels by removing the locking pin from the securing bracket. Take hold of the loop
handle and tip it towards you so that it clears the square tube at the top of the main
frame between the black handles. With the other hand lower the main frame until
the square tube comes to rest on the slotted bracket about 12cm above the castor
wheels, as shown in (fig.4). Fold up the load restraint at the other end of the frame
until it rests against the platform.
5.5. Manoeuvre the loaded trolley using the loop handle only. DO NOT lift the truck by the
black handles when used in flat bed configuration.
WARNING! When changing truck positions keep fingers well clear of all pinch points.
‰
© Jack Sealey Limited
SACK TRUCK 3-IN-1
PNEUMATIC TYRES 250KG CAPACITY
CST989.V3
MODEL NO:
Original Language Version
fig.1
fig.2
CST989.V3 | Issue 1 15/05/19