Height Adjustment - Chicco Polly2Start Manual

safety harness (Fig. 4), the cover B15 must be fitted from
the top to the bottom until it fits in the backrest part
(Fig. 5).
Put the cover B15 on the seat B, inserting the safety har-
ness B14 in appropriate cover holes. Make sure that the
positions of the holes on the fabric cover correspond to
those on the backrest.
To complete fitting the cover, fasten the buttons B16 on
the rear flaps of the cover to the holes B17 on the back
of the high chair backrest (Fig.6).
SAFETY HARNESS
WARNING: The use of the safety harness with fabric crotch
strap is essential to guarantee the safety of your child.
WARNING: The tray alone does not guarantee the safe-
ty of your child. Always use the safety harness!
The high chair has a 5-point safety harness.
Release the safety harness, place the child on the high
chair and secure the child with the harness, adjusting its
length so it suits the child.
The safety harness can be adjusted to two height positions.
The buckle may be released by pressing the forks.
The width of the waist belts can be adjusted using the
relevant sliding rings (Fig. 7).
TRAY POSITIONING/ADJUSTMENT
The tray can be adjusted to 4 different positions.
To fasten the tray, turn the armrests B5 and make sure
that they are locked in horizontal position (Fig. 8).
Insert the armrests in the guides below the tray, keep-
ing the central fastening button C2 pressed (Fig. 9).
Move the tray to the desired position and release the
button. If the tray is not automatically locked on the
armrests, move the tray until a click is heard, indicating
that the tray has locked.
WARNING: before use, always check the correct fasten-
ing of the tray on the armrests.
WARNING: the tray may only be adjusted to the 4 indi-
cated positions.
WARNING: never leave the tray fitted in a position in
which the danger signs are visible on the armrests: This
position is NOT safe!
WARNING: When the tray is fitted on the product,
make sure to avoid the inadvertent pressing of the arm-
rest tilting buttons.
To remove the tray, press the central button C2. When
not in use, the tray may be fastened to the rear of the
structure (Fig. 10) in the relevant slots A4. The high chair
is equipped with a tray cover C1. It can be fastened to
the tray sides with a pressure mechanism.
WARNING: When in use, always make sure that the tray
is correctly fastened. If the child eats at the table with
the parents, the tray cover may be used as a convenient
place mat.
WHEELS
The rear legs feature swivel wheels with brakes (A6)
The front legs of the high chair are equipped with one-
way wheels A3 to facilitate the handling and the open-
ing/closing operations.
WARNING: always place the chair on a horizontal, sta-
ble surface. Never place the high chair near stairs or
steps.
To activate the high chair brakes, lower the wheel lock-
ing levers. To release the wheels, repeat in reverse order
(Fig. 10A).

HEIGHT ADJUSTMENT

The high chair can be adjusted to 8 height positions.
To raise the seat, hold the upper part of the backrest and
pull it upwards, until the desired height is reached (Fig. 11).
To lower the seat, press the two B1 buttons at the
same time, lowering the seat until the desired height is
reached (Fig.12).
WARNING: do not carry out this operation with the
child sitting in the high chair.
HOW TO CLOSE THE CHAIR
WARNING: when performing this operation, ensure
that your child, or other children, are at a safe distance.
Make sure that during these operations the removable
parts of the high chair do not come into contact with
your child.
• Place the backrest in vertical position (Fig. 13), remove
the tray and fit it to the rear legs, then tilt the armrests
by pressing the buttons B6 (Fig. 14).
• Completely lower the seat by pressing the two height
adjustment buttons B1 at the same time.
• Press the opening/closing buttons A5 located at the
centre of the lateral joints and at the same time ap-
proach the legs of the high chair (Fig.15).
LEGREST
The high chair is equipped with a legrest B2 that can be
adjusted to 3 positions of use; press the two buttons B4
and tilt the legrest until reaching the desired position.
WARNING: The legrest can turn upward to non-usable
positions (Fig. 16)
FOOTREST
The high chair is equipped with a footrest B3 that can
be adjusted to 4 height positions. From the currently
used position turn it upwards until it unlocks. Remove
the footrest and fit it at the desired height.
HOW TO ADJUST THE WIDTH OF THE BACKREST
The width of the backrest of this high chair can be ad-
justed to ensure maximum comfort for your child at
every stage of growth.
To adjust the width, use the wheel B12 at the top center
of the backrest turning it left or right until you reach the
desired width.
To activate rotation, use the button B13 on the back of
the wheel by pulling it up and turn the wheel at the
same time (Fig.17).
RECLINED CRADLE (0m+)
RECLINED CRADLE USE WARNING
• WARNING: Never leave the child unattended.
• WARNING: Do not use the toy bar to carry the re-
10