Page 1
TURBO HD H8T Series Bullet & Turret Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type...
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Page 3
Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
To avoid heat accumulation, good ventilation is required for the operating environment. Keep the camera away from liquid while in use for non- water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark...
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ...
Page 6
For cement wall, expansion bolts are required to fix the camera. For wooden wall, self-tapping screws are required. 5. Connect the corresponding power cord, and video cable. 6. Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the surveillance angle.
Page 7
Figure 2-5 Fix the Camera with the Junction Box 5. Attach the junction box’s body to the ceiling by aligning the screw holes of the junction box. 6. Secure the junction box’s body with supplied screws on the ceiling. Junction Box Body Screw Figure 2-6 Fix the Camera to the Ceiling...
Page 8
Note: Drill the cable hole, when adopting the ceiling outlet to route the cable. 3. Loosen screws to remove the clip plate, and take out the main body. Figure 2-9 Remove the Clip Plate 4. Fix the mounting base on the ceiling with supplied screws.
Page 9
Pan Position [0° to 360°] Tilt Position [0° to 75°] Rotation Position [0° to 360°] Figure 2-12 3-axis Adjustment 1). Hold the camera body and rotate the enclosure to adjust the pan position [0° to 360°]. 2). Move the camera body up and down to adjust the tilt position [0°...
Page 10
Figure 2-15 Secure the Junction Box’s Body on Ceiling 7. Combine the junction box cover with its body by tightening four screws on junction box’s cover. Figure 2-16 Fix the Junction Box 8. Repeat steps 5 to 9 of 2.2.1 Ceiling Mounting without Junction Box to complete the installation.
3 Menu Description Please follow the steps below to call the menu. Note: The menu description part is only for your reference. It might have some differences due to the specific model that you have. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1.
3). Click left/right direction button to adjust the value of the selected item. 3.1 VIDOE FORMAT You can set the video format as 5MP@20fps, 4MP@25fps, 4MP@30fps, 2MP@25fps, and 2MP@30fps. Note: When switching the video output as CVBS, you can set the video format as PAL, or NTSC.
Figure 3-4 B & W IR LIGHT You can turn on/off the IR LIGHT to meet the requirements of different circumstances. SMART IR The Smart IR function is used to adjust the light to its most suitable intensity, and prevent the image from over exposure.
VIDEO SETTINGS IMAGE MODE WHITE BALANCE BRIGHTNESS CONTRAST SHARPNESS SATURATION 3DNR MIRROR BACK EXIT SAVE & EXIT Figure 3-6 VIDEO SETTINGS IMAGE MODE IMAGE MODE is used to adjust the image saturation, and you can set it as STD (Standard), or HIGH-SAT (High Saturation).
MIRROR OFF, H, V, and HV are selectable for mirror. OFF: The mirror function is disabled. H: The image flips 180° horizontally. V: The image flips 180° vertically. HV: The image flips 180° both horizontally and vertically. 3.5 FUNCTIONS In the FUNCTIONS submenu, you can set the motion detection, and privacy mask of the camera.