Table of Contents
Advertisement
Quick Links
TURBO HD
H8T Series
Bullet & Turret Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Type
Model
DS-2CE19H8T-(A)IT3ZF
Type I Camera
Type II Camera
DS-2CE79H8T-IT3ZF
This manual may contain technical incorrect places or
printing errors, and the content is subject to ch8ange
without notice. The updates will be added to the new
version of this manual. We will readily improve or update
the products or procedures described in the manual.
0100001080730
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CE19H8T-IT3ZF
Summary of Contents for HIKVISION DS-2CE19H8T-IT3ZF
- Page 1 TURBO HD H8T Series Bullet & Turret Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Type Model DS-2CE19H8T-(A)IT3ZF Type I Camera...
-
Page 2: Regulatory Information
Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
- Page 4 To avoid heat accumulation, good ventilation is required for the operating environment. Keep the camera away from liquid while in use for non- water-proof device. While in delivery, the camera shall be packed in its original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark...
-
Page 5: Installation
2 Installation Before you start: Make sure that the device in the package is in good condition and all the assembly parts are included. Make sure that all the related equipment is power-off during the installation. Check the specification of the products for the ... - Page 6 For cement wall, expansion bolts are required to fix the camera. For wooden wall, self-tapping screws are required. 5. Connect the corresponding power cord, and video cable. 6. Power on the camera to check whether the image on the monitor is gotten from the optimum angle. If not, adjust the surveillance angle.
- Page 7 Figure 2-5 Fix the Camera with the Junction Box 5. Attach the junction box’s body to the ceiling by aligning the screw holes of the junction box. 6. Secure the junction box’s body with supplied screws on the ceiling. Junction Box Body Screw Figure 2-6 Fix the Camera to the Ceiling...
- Page 8 Note: Drill the cable hole, when adopting the ceiling outlet to route the cable. 3. Loosen screws to remove the clip plate, and take out the main body. Figure 2-9 Remove the Clip Plate 4. Fix the mounting base on the ceiling with supplied screws.
- Page 9 1). Hold the camera body and rotate the enclosure to adjust the pan position [0° to 360°]. 2). Move the camera body up and down to adjust the tilt position [0° to 75°]. 3). Rotate the camera body to adjust the rotation position [0°...
-
Page 10: Menu Description
8. Repeat steps 5 to 9 of 2.2.1 Ceiling Mounting without Junction Box to complete the installation. 3 Menu Description Purpose: Call the menu by clicking the button on the PTZ Control interface, or call preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. -
Page 11: Exposure Mode
2). Click Iris + to confirm the selection. 3). Click left/right direction button to adjust the value of the selected item. 3.1 VIDOE FORMAT You can set the video format as 5MP@20fps, 4MP@25fps, 4MP@30fps, 2MP@25fps, and 2MP@30fps. Note: When switching the video output as CVBS, you can ... -
Page 12: Video Settings
You can turn on/off the IR LIGHT and set the value of SMART IR in this menu DAY/NIGHT B & W MODE IR LIGHT SMART IR BACK EXIT SAVE & EXIT Figure 3-4 B & W IR LIGHT You can turn on/off the IR LIGHT to meet the requirements of different circumstances. -
Page 13: Image Mode
VIDEO SETTINGS IMAGE MODE WHITE BALANCE BRIGHTNESS CONTRAST SHARPNESS SATURATION 3DNR MIRROR BACK EXIT SAVE & EXIT Figure 3-6 VIDEO SETTINGS IMAGE MODE IMAGE MODE is used to adjust the image saturation, and you can set it as STD (Standard), or HIGH-SAT (High Saturation). -
Page 14: Factory Default
MIRROR OFF, H, V, and HV are selectable for mirror. OFF: The mirror function is disabled. H: The image flips 180° horizontally. V: The image flips 180° vertically. HV: The image flips 180° both horizontally and vertically. 3.5 FUNCTIONS In the FUNCTIONS submenu, you can set the motion detection, and privacy mask of the camera.