Appendix; Precautions; Error Messages - Sony HKCU-IP43F Operation Manual

Appendix

Precautions

If the unit is suddenly taken from a cold to a warm location, or
if ambient temperature suddenly rises, moisture may form on
the outer surface of the unit and/or inside of the unit. This is
known as condensation. If condensation occurs, turn off the
unit and wait until the condensation clears before operating
the unit. Operating the unit while condensation is present may
damage the unit.
The fan and battery are consumable parts that will need
periodic replacement.
When operating at room temperature, a normal replacement
cycle will be about 5 years. However, this replacement cycle
represents only a general guideline and does not imply that
the life expectancy of these parts is guaranteed. For details on
parts replacement, contact your Sony representative.
The life expectancy of the electrolytic capacitor is about 5
years under normal operating temperatures and normal usage
(8 hours per day; 25 days per month).
If usage exceeds the above normal usage frequency, the life
expectancy may be reduced correspondingly.
Do not push the mesh portion of the front panel with your
fingers or sharp objects.
Operating environment
• Avoid high-temperature rooms and near sources of heat.
• Do not place in locations with strong electric or magnetic
field.
• Dry location with good ventilation.
• Avoid locations exposed to sunlight or strong lighting.
Avoid violent impacts
Dropping the unit, or otherwise imparting a violent shock to it,
is likely to cause it to malfunction.
Do not cover with cloth
While the unit is in operation, do not cover it with a cloth or
other material. This can cause the temperature to rise, leading
to a malfunction.
After use
Set the POWER switch to the OFF position.
Care
If the body or panels of the unit become dirty, wipe them with
a dry cloth. For severe dirt, use a soft cloth steeped in a small
amount of neutral detergent, then wipe dry. Do not use volatile
solvents such as alcohol or thinners, as these may damage
the finish.
To prevent electromagnetic interference from
portable communications devices
The use of portable telephones and other communications
devices near this unit can result in malfunctions and
interference with audio and video signals.
It is recommended that the portable communications devices
near this unit be powered off.

Error Messages

When an error is detected in this unit or the camera, the
ALARM indicator turns on and an error message is displayed
on this unit.
Error message
CCU:GENLOCK ERROR
CCU:10FIELD-ID ERROR
CCU:FORCE LEGACY
CCU:PS FAN STOP
CCU:PS CABLE SHORT
CCU:PS CABLE OPEN
CCU:PS RCP POWER SUPPLY
ERROR
CCU:PS TEMP WARNING
CCU:DVP FAN STOP
CCU:OPTICAL CONDITION
ERROR
CCU:OPTICAL CONDITION
WARNING
CCU:OPTICAL CONDITION
CARE
CCU:COMMAND ERROR
CCU:XXX POWER ERROR
CCU:XXX PLD ERROR
CCU:XXX TEMP WARNING
CCU:OPT NO OPTION
CCU:PLEASE UPDATE
CAMERA SOFTWARE
CCU:PLD CONFIG ERROR
63
Description
External reference sync error
10Field ID is not detected even
though the 10F BB setting is On
FORCE LEGACY is set for CNS
MODE
Power supply block FAN error
CAMERA connector optical fiber
cable short circuit error
CAMERA connector optical fiber
cable open circuit error
Remote control panel
(connected to REMOTE
connector) power supply error
Power supply unit temperature
error
DVP board fan stopped
Light sensor level on CCU side
dropped
Command communication error
of camera and remote control
panel
Board power supply section
error (XXX is the board name)
PLD error (XXX is the PLD
name)
Board temperature error (XXX is
the board name)
Option key required for when
CHU MODE is set to HDC(HD
CUTOUT) is not installed.
There is a software version
mismatch between the camera
and this unit.
DPR PLD is not configured for
HD CUTOUT when CHU MODE
is set to HDC(HD CUTOUT).