Advertisement
Available languages
Available languages
www.jts-germany.de
These instructions are intended for
ENGLISH
users without any specific technical
knowledge. Please read the instruc-
tions carefully prior to operation and
keep them for later reference.
1 Applications
Combined with a suitable receiver (US-8001D/1,
US-8002D/1), the headband microphone UT-16HW/1
with miniature transmitter creates a wireless audio
transmission system. The microphone is ideally suited
for any application requiring total mobility.
For wireless transmission, 16 channels are avail-
able in the frequency range 863 – 865 MHz. When
you operate several headband microphones at the
same time, you will be able to use different channels
without interference.
1.1 Conformity and approval
Herewith, MONACOR INTERNATIONAL declare that
the microphone UT-16HW/ 1 complies with the
directive 2014/53/EU. The EU declaration of con-
formity is available on request from MONACOR
INTER NATIONAL. The unit is licence-free and gener-
ally ap proved for operation in EU and EFTA countries.
2 Important Notes
This unit corresponds to all relevant directives of the
EU and is therefore marked with
•
The unit is suitable for indoor use only. Protect it
against dripping water, splash water and high air
humidity. The admissible ambient temperature
range is 0 – 40 °C.
•
For cleaning only use a dry, soft cloth; never use
water or chemicals.
•
No guarantee claims for the unit and no liability for
any resulting personal damage or material damage
will be accepted if the unit is used for other pur-
poses than originally intended, if it is not correctly
operated, or if it is not repaired in an expert way.
If the unit is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment.
3 Operation
1) Remove the battery compartment cover (4). Insert
a battery of size AAA as indicated in the battery
compartment, then replace the cover.
If the microphone is not in use for a longer pe-
riod of time, remove the battery to prevent damage
to the transmitter due to battery leakage.
Never put batteries in the household waste.
To protect the environment, always take
them to a special waste disposal, e. g. collec-
tion container at your retailer
2) Set the transmitter and the receiver to the same
channel: Turn the switch (7) with the adjusting
key (8) in such way that the flat side of the axle
points to the desired channel number. The figure
on the right shows the setting for channel 5. The
16 channels are assigned to the following trans-
mission frequencies:
Vertrieb von JTS-Produkten – Distrubution of JTS products
Channel
1
2
3
4
5
6
7
8
If you use several headband microphones at the
same time, set a different channel for each pair of
transmitter and receiver. To distinguish between
different transmission channels, replace the battery
compartment cover by the white or orange cover
supplied with the microphone.
3) Place the wind shield / pop shield (12) on the
microphone (11).
4) Switch on the microphone with the button
ON / OFF / MUTE (5); the power LED (6) shows
green. If it shows orange, replace the battery. To
mute the microphone (the power LED starts flash-
ing) or to unmute it, briefly press the button once
again.
To switch off the microphone later, keep the
button pressed until the power LED is extinguished.
5) To set the microphone sensitivity, use the control
.
GAIN (2): If the volume of the microphone signal
is too high and the signal is distorted, turn back the
control with the adjusting key (8). If, on the other
hand, the volume of the signal is too low, there
will be a poor S / N ratio. In this case, turn up the
control accordingly.
6) To protect the transmitter from impurities, cover
it with the rubber cap (13) provided. Place the
microphone and align the gooseneck (10) in such
a way that it is close to your mouth. To adapt it to
your head size, release the locking nuts (1) and
then adjust the head strap (3) accordingly.
4 Specifications
Radio frequency range: . . . 863 – 865 MHz for
Transmitting power: . . . . . . < 10 mW
Frequency stability: . . . . . . . ±0.005 %
Audio frequency range: . . . 100 Hz – 18 kHz
max. SPL: . . . . . . . . . . . . . . 120 dB
Type of microphone: . . . . . electret microphone,
Power supply: . . . . . . . . . . . 1.5 V battery, size AAA
Operating time: . . . . . . . . . . > 8 h
Dimensions
of transmitter: . . . . . . . . . . . 89 × 23 × 27 mm
Weight (w/o battery): . . . . . 50 g
Subject to technical modification.
®
MONACOR INTERNATIONAL GmbH & Co. KG, Zum Falsch 36, 28307 Bremen, Germany
Copyright
Frequency
Channel
Frequency
863.125 MHz
9
864.125 MHz
863.250 MHz
10
864.250 MHz
863.375 MHz
11
864.375 MHz
863.500 MHz
12
864.500 MHz
863.625 MHz
13
864.625 MHz
863.750 MHz
14
864.750 MHz
863.875 MHz
15
864.875 MHz
864.000 MHz
16
865.000 MHz
channels see table above
cardioid
©
by MONACOR INTERNATIONAL. All rights reserved.
UT-16HW/1
Order number 25.4640
Headband Microphone
with Miniature Transmitter
863 – 865 MHz
ON / OFF
MUTE
CH
1
2
3
ON / OFF
MUTE
1 Locking nuts for the head strap (3)
2 Control GAIN for the microphone sensitivity
3 Head strap
4 Battery compartment cover
5 Button ON / OFF/ MUTE
To switch off, keep the button pressed until the
power LED (6) is extinguished.
6 Power LED
green = battery charged sufficiently
orange = replace battery
flashing green = microphone muted
7 Channel selector switch (figure shows channel 5
selected)
8 Adjusting key for the channel selector switch (7)
and the control GAIN (2)
9 Headband
10 Gooseneck
11 Microphone
12 Wind shield / pop shield
13 Protective rubber cap
A-1386.99.02.01.2016
4
5
6
1
5
7
9
8
9
10
11
12
13
Advertisement
