Related Manuals for Parker LP28 Series
Summary of Contents for Parker LP28 Series
- Page 1 Manual No. 102-0615-01 Rev. 2 LP/LD28 Series Parker Product Manual Effective: August 2, 2006 Supersedes: March 15, 2006 Electromechanical Positioning Systems Automation...
-
Page 2: Important User Information
The products described herein, including without limitation, product features, specifications, designs, availability and pric- ing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. The information in the product manual, including any apparatus, methods, techniques, and concepts... -
Page 3: Table Of Contents
CHAPTER 5 - MAINTENANCE AND REPAIR ........................22 ................................22 UBRICATION NEMA 11 M ...........................22 OTOR NSTALLATION NEMA 17 M ...........................24 OTOR NSTALLATION ..........................26 EADSCREW RELOAD DJUSTMENT APPENDIX A - ACCESSORIES & SPARE PARTS ......................27 Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 4: Revision Notes
Updated Speed Versus Thrust Graphs, Page 15 Added RMS Current Spec, Page 17 Added Min Toe Clamp Spacing and Number of Clamps for LP28, Page 19 Updated NEMA 17 Motor Adapter Dims, Page 27 Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 5: Chapter 1 - Introduction
DO NOT drill holes into the positioner. Drilling holes into the positioner can generate particles and machining forces that may effect the operation of the positioner. Parker will drill holes if neces- sary; contact your local authorized distributor. DO NOT subject the unit to impact loads such as hammering, riveting, etc. Impacts loads generated by hammering or riveting may result in flat spots on bearing surfaces or misalignment of drive components. -
Page 6: Return Information
Return Information Returns All returns must reference a “Return Material Authorization” (RMA) number. Please call your local author- ized distributor or Parker Customer Service Department at 800-245-6903 to obtain an “RMA” number. Repair Information Out-of-Warranty Repair Our Customer Service Department repairs Out-of-Warranty products. All returns must reference an “RMA”... -
Page 7: Specification Conditions
Catalog specifications and specifications in this manual are measured from the center of the carriage, 37.5mm above the carriage surface. All measurements taken at any other location may deviate from these values. Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 8: Assembly Diagrams
LP/LD28 Series Product Manual Assembly Diagrams LP28 Stepper Motor Load Plate Leadscrew Base Carriage Toe Clamp Leadscrew Nut Square Rail Limit/Home Switches Bearing End Cap LD28 Stepper Motor Base Leadscrew Nut Toe Clamp Leadscrew Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 9: Chapter 2 - Lp/Ld28 Specifications
LP/LD28 Series Product Manual Chapter 2 - LP/LD28 Specifications Order Number Nomenclature - LP28 Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... - Page 10 LP/LD28 Series Product Manual Order Number Nomenclature - LD28 Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania...
-
Page 11: Dimensional Drawings - Lp28
Dimensional Drawings - LP28 NEMA 17 Motor (M71xx Option) Motor Option “A” M11xx 31.5 Visit www.parkermotion.com M13xx 50.6 for 2D CAD and 3D Models M71xx 50.0 Single Bearing Truck (G21 Option) Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... - Page 12 LP/LD28 Series Product Manual Dimensional Drawings - LP28 Limit/Home Switch and Toe Clamp Accessories LP28 Idler (D00 Option) Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania...
-
Page 13: Dimensional Drawings - Ld28
Leadscrew Nut Detail NEMA 17 Motor (M71xx Option) Motor Option “A” M11xx 31.5 M13xx 50.6 M71xx 50.0 Visit www.parkermotion.com for 2D CAD and 3D Models End View Including Accessory Toe Clamps Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 14: Performance Specifications - Lp28
0.38 (0.84) 0.47 (1.04) 0.51 (1.12) Weight of Additional Travel Length - Kgf/mm (lbs/mm) 0.0015 (0.0033) Unit weight based on double bearing truck with no limit/home switches. Other options will vary slightly. Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... - Page 15 20 rps, they pass through a resonance which adversely and unpredictably affects useable motor torque. For applications requiring higher speeds, Parker recommends using a faster lead or a servo motor. Applications using a stepper motor above this recom- mended limit must be fully tested and qualified by the user.
-
Page 16: Performance Specifications - Ld28
M11xx Option M13xx Option M71xx Option Unit Weight (Basic Unit with Zero Travel) - Kgf (lbs) 0.18 (0.40) 0.27 (0.60) 0.32 (0.71) Weight of Additional Travel Length - Kgf/mm (lbs/mm) 0.0002 (0.0004) Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 17: Chapter 3 - Component Specifications
Notes None None Orange and Brown If using Parker ViX drive, default positive direction is opposite other Parker products. To account for this, reverse a phase by interchanging B+ and B- when using ViX drive. Switching Sequence Step CCW Rota-... -
Page 18: Limit/Home Switch Information
Reverse Polarity Protection Short Circuit Protection Power-Up Pulse Suppression Enclosure Rating IP67 Operating Temperature Range -25°C to +75°C Cable Length 3.0 m Wiring Code Power (+) Brown Output Signal Black Ground (-) Blue Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 19: Chapter 4 - Setup And Usage
M2 square nuts are intended for use in the T-slots. See Chapter 2 for slot location and Appendix A for square nut drawing and part number. Toe Clamp Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 20: Payload Mounting - Lp28
Further, extreme care should be taken not to travel the leadscrew nut so that it makes contact at the fixed end, because this will change preload setting and possibly cause damage. Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 21: Limit/Home Switch Adjustment - Lp28
These numbers are pro- H2 or L2 003-3743-07 P8S-GMFLX vided in the table to the right: H3 or L3 003-3743-05 P8S-GNFLX H4 or L4 003-3743-08 P8S-GQFLX H5 or L5 003-3743-06 P8S-GPFLX Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 22: Chapter 5 - Maintenance And Repair
Step 4: IF INSTALLING NEW COUPLING HUB ON MOTOR SHAFT: Apply Loctite 638 to coupling bore. Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... - Page 23 Rotate motor into proper orientation. Note standard orien- tation from factory is such that the motor leads or cable are toward limit/ home switches. Step 9: Install pan head screws and tighten evenly as wave spring compresses. Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania...
-
Page 24: Nema17 Motor Installation
Apply Loctite 638 to coupling bore. Step 6: IF INSTALLING NEW COUPLING HUB ON MOTOR SHAFT: Place coupling hub onto motor shaft. Position hub so surface is flush with end of shaft as shown. Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... - Page 25 Rotate motor into proper orientation. Note standard orien- tation from factory is such that the motor leads or cable are toward limit/ home switches. Step 11: Install socket head cap screws and tighten. Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania...
-
Page 26: Leadscrew Preload Adjustment
Step 6: LP28 ONLY: Slide drive train into positioner base taking care when installing bearing trucks onto rail and inserting leadscrew into endcap bore. Step 7: Reinstall motor. See previous section for procedure. Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... -
Page 27: Appendix A - Accessories & Spare Parts
Toe Clamp 101-1567-01 NEMA 17 Motor Adapter C*LV171-02-10 Motor, NEMA 17 Single Stack, Rear Shaft, 10’ Cable - For M7122 Option 003-3908-01 M2 Square Nut 101-1564-01 Toe Clamp 101-1567-01 NEMA17 Motor Adapter Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania... - Page 28 LP/LD28 Series Product Manual Notes Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania...
- Page 29 LP/LD28 Series Product Manual Notes Parker Hannifin Corporation EMN Automation - Parker Irwin, Pennsylvania...
- Page 30 Parker Hannifin Corporation Electromechanical Automation Divi- sion 1140 Sandy Hill Road Irwin, PA 15642 Tel: (800) 245-6906 www.parkermotion.com Email: emn_sales@parker.com emn_support@parker.com...