Toshiba RAV-RM301SDT-E Installation Manual page 62

◆ Procedure example ➀
Manual address setup procedure
While the operation stops, change the setup.
(Be sure to stop the operation of the unit.)
3
-2,
4
-2,
5
-2
7
1 2,6
1
Procedure
Push simultaneously + + buttons for 4 seconds or
more. After a while, the display part flashes as shown below.
Check the displayed CODE No. is [10].
• When the CODE No. is other than [10], push
erase the display and repeat procedure from the first step.
(After pushing button, operation of the remote
controller is not accepted for approx. 1 minute.)
(For a group control, No. of the firstly displayed indoor unit
becomes the header unit.)
(* Display changes according to
the model No. of indoor unit.)
2
Procedure
Every pushing button, the indoor unit No. in the
group control is displayed in order. Select the indoor unit of
which setup is changed.
In this time, the position of the indoor unit of which setup is
changed can be confirmed because fan of the selected
indoor unit operate.
3
Procedure
1
Using temp. setup / buttons, specify
CODE No. [12].
(CODE No. [12]: Line address)
2
Using timer time / buttons, change the line
address from [3] to [2].
3
Push button.
In this time, the setup finishes when the display changes
from flashing to lighting.
121-EN
Indoor unit No. before setup change is displayed.
7
3
-1,
4
-1,
5
-1,
4
Procedure
1
Using temp. setup /
CODE No. [13].
3
-3,
(CODE No. [13]: Indoor address)
4
-3,
2
5
Using timer time / buttons, change the
-3,
indoor address from [3] to [2].
3
Push button.
In this time, the setup finishes when the display changes
from flashing to lighting.
Indoor unit No. before setup change is displayed.
button to
5
Procedure
1
Using temp. setup /
CODE No. [14].
(CODE No. [14]: Group address)
2
Using timer time / buttons, change the setup
data from [0001] to [0002].
(Setup data [Header unit: 0001] [Follower unit: 0002])
3
Push button.
In this time, the setup finishes when the display changes
from flashing to lighting.
Indoor unit No. before setup change is displayed.
– 61 –
6
Procedure
If there is other indoor unit to be changed, repeat procedure
2 5
to to change the setup.
When the above setup has finished, push
the indoor unit No. before change of setup, specify CODE
No. [12], [13], [14] in order with temp. setup
buttons, and then check the changed contents.
Address change check Before change:
[3-3-1]  After change: [2-2-2]
Pushing button clears the contents of which setup was
changed.
(In this case, procedure from
buttons, specify
Indoor unit No. before setup change is displayed.
7
Procedure
After check of the changed contents, push
is determined.) When pushing
disappears and the status becomes the usual stop status.
(When pushing
buttons, specify
controller is not accepted for approx. 1 minute.)
* If the operation from the remote controller is not accepted
even 1 minute or more passed after pushing
is considered that the address setup is incorrect.
In this case, the automatic address must be again set up.
Therefore repeat procedure of the setup change from the
1
Procedure
◆ To recognize the position of the
corresponding indoor unit though
the indoor unit No. is known
to select
Check the position during operation stop.
/
(Be sure to stop operation of the set.)
2
is repeated.)
Procedure
Push simultaneously
more.
After a while, the display part flashes and the display appears
as shown below.
In this time, the position can be checked because fan of the
indoor unit operate.
• For the group control, the indoor unit No. is displayed as
[
operate.
Check the displayed CODE No. is [01].
• When the CODE No. is other than [01], push
button. (Setup
erase the display and repeat procedure from the first step.
button, the display
(After pushing
is not accepted for approx. 1 minute.)
button the operation from the remote
button, it
.
Procedure
In the group control, every pushing
indoor unit No. in the group control is displayed in order.
In this time, the position of the indoor unit can be confirmed
because only fan of the selected indoor unit operate.
(For a group control, No. of the firstly displayed indoor unit
becomes the header unit.)
1
2
1,3
1
+ buttons for 4 seconds or
] and fans of all the indoor units in the group control
button to
button, operation of the remote controller
(* Display changes according to
the model No. of indoor unit.)
2
button, the
122-EN