Ruckus Wireless ZoneFlex 7441 Quick Setup Manual

ZoneFlex 7441 Dual Band
802.11n DAS Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions on
how to set up your Ruckus Wireless ZoneFlex Access Point. After
completing the steps described in this Guide, you will be able to
place the Access Point (AP) at your site and provide wireless
network access to users.
The ZoneFlex 7441 requires a minimum of Zone-
NOTE:
Flex firmware version 9.7 and above to operate.
T G O L
HIS UIDE IN THER ANGUAGES
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com.
請造訪以下網址，取得此手冊的繁體中文版本
https://support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com.
こ の ガ イ ド の⽇本語版は
https://support.ruckuswireless.com
で ご 覧 く だ さ い。
이 가이드의 한국어 버전은 웹 사이트
(https://support.ruckuswireless.com) 에서 확인하시기 바랍니다 .
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com.
B Y B
EFORE OU EGIN
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
• Release Notes and User Guides are available at
http://support.ruckuswireless.com/documents
• Software Upgrades, Open Source Information and Product
Warranty/Software License Agreement documents are also
available at: http://support.ruckuswireless.com/
Copyright © 2013 Ruckus Wireless, Inc.
Published June 2013, Part Number 800-70437-001 Rev B
P C
ACKAGE ONTENTS
• ZoneFlex 7441 Access Point
• Mounting Brackets
• Mounting accessory bag (DIN rail clip, 4 screws for mounting
ears, terminal ring for ground wire, 4 rubber feet)
• Product Warranty Statement
• This Quick Setup Guide
S R
ETUP EQUIREMENTS
• A computer running Windows 7 (procedures for other OS's
are similar)
• One or more of the following:
• A modem (DSL or cable), broadband router, or other
device provided by your Internet Service Provider that
brings Internet access to your site.
• A network switch or a DSL/Internet gateway device.
• An Ethernet cable (Cat5e or better for PoE in)
• An AC power adapter (sold separately), or
• An 802.3af or 802.3at -compliant Power over Ethernet (PoE)
switch or PoE injector, or
• AC/DC adapter 12V 1.5A (Ruckus part #902-0169-xx00, or
equivalent)
S 1: C
TEP ONNECT THE
Figure 1. ZoneFlex 7441 DAS Access Point
1 After removing your Ruckus Wireless AP from its package,
place it next to your computer.
2
Using an Ethernet cable, connect your computer's network
.
port to the 10/100/1000 port on the AP.
3 Using the AC adapter (sold separately), connect the AP to a
convenient (and protected) power source.
• Alternatively, connect the 10/100/1000 port to a PoE
injector or PoE switch for both power and network con-
nectivity.
4
Verify that the Power LED on the external enclosure is a
steady green.
AP Y C
TO OUR OMPUTER
S 2: P Y C
TEP REPARE OUR OMPUTER FOR
S
ETUP
NOTE:
The following procedures assume Windows 7 as the
operating system. Procedures for other OS's are similar.
1
On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as follows:
Start > Control Panel > Network and Sharing
•
Center > Change Adapter Settings
2 Edit the TCP/IPv4 address settings as follows:
Local Area Connection > Properties > Internet
•
Protocol Version 4 (TCP/IPv4) > Properties
The TCP/IPv4 Properties dialog box appears.
3 Use the following IP address
Select
selected) and then make the following entries:
IP address
• : 192.168.0.22 (or any address in the
192.168.0.x network)
Subnet mask
• : 255.255.255.0
Default gateway
• : 192.168.0.1
DNS server
Leave the fields empty.
OK
4 Click to save your changes.
Your changes are put into effect immediately.
S 3: L I AP
TEP OG NTO THE
As specified earlier, the AP should be directly connected to your
computer (through the Ethernet port) and powered on, ready for
setup.
1
On your computer, open a Web browser window.
2 In the browser, type this URL to connect to the AP:
https://192.168.0.1
3 Press <Enter> to initiate the connection. When a security
OK/Yes
alert dialog box appears, click
4 When the Ruckus Wireless Admin login page appears, enter
the following:
Username
• : super
Password
• : sp-admin
5 Login
Click .
Default AP Settings (For Your Reference)
Network Names Wireless1—Wireless8 (2.4 GHz radio)
(SSIDs) Wireless9—Wireless16 (5 GHz radio)
Security (Encryption Disabled for each wireless interface
method)
AP
(if it is not already
to proceed.
Page 1 of 2