Common Cli Commands; Manually Configuring The Unit's Ip Address - ADTRAN Total Access 900E Series Quick Start

g
NOTE
There are many terminal emulation applications available on the web. PuTTy, SecureCRT, and HyperTerminal
are a few examples.
1. Connect the DB-9 (male) connector of your serial cable to the port labeled CRAFT on the back panel of
the unit.
2. Connect the other end of the serial cable to the terminal or PC.
g
NOTE
Many PCs do not come with a standard serial port. A universal serial bus (USB) to serial adapter can be used
instead. The drivers for the USB to serial adapter must be installed according to the manufacturer's instructions.
If the USB to serial adapter is not properly installed on your PC, you will not be able to communicate with the
AOS unit and you should seek support from the USB to serial adapter manufacturer.
3. Provide power to the unit as appropriate. Refer to the
Guide available online at
4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8
data bits, no parity bits, 1 stop bit, and no flow control. Press ENTER to activate the AOS CLI.
5. Enter enable at the > prompt and enter the Enable mode password when prompted. The default
password is password.
You can also access the CLI from a Telnet or SSH client. In order to do this, you must know the IP address of
the Total Access device. If you do not know the unit's IP address, you must use the port labeled CRAFT to
access the CLI. To access the CLI using a Telnet or SSH client, follow these steps:
1. Connect the Total Access unit to your PC or to an existing network that supports DHCP using an Ether-
net cable connected to the port labeled GIG 0/1 on the back of the device.
2. Open a Telnet or SSH client on your computer and enter 10.10.10.1. If your unit received an IP address
from a DHCP server or you have changed your unit's IP address, you will need to enter that address.
3. For SSH, log into the unit using the default login (admin) and password (password). For Telnet, only the
default password (password) is required.
4. Enter enable at the > prompt and enter the enable password when prompted. The default password is
password.
C CLI C
OMMON
The following are common CLI commands and tips for getting started with the CLI.
■
Entering a question mark (?) shows contextual help and options. For example, entering ? at the prompt will
show all commands available from that prompt.
■ To view interface statistics, enter show interfaces <interface type> <interface number>.
■ To view the current configuration, enter show running-config.
■
To view all the IP Addresses currently configured, enter show ip interfaces brief.
■ To view the AOS version, serial number, and other information, enter show version.
■
To save the current configuration, enter write.
M C
ANUALLY
g
NOTE
The configuration parameters used in the examples outlined in this guide are for instructional purposes only.
Replace all underlined entries (example) with your specific parameters to configure your application.This step
is unnecessary if the unit's IP address has been configured automatically using DHCP.
The following steps create an IP address and subnet mask for GIG 0/1. If you are not sure what IP address to
assign, please contact your network administrator.
1. At the # prompt, enter config terminal.
2. At the (config)# prompt, enter interface g 0/1 to access the configuration parameters for the GIG 0/1
port located on the back of the unit.
3. Enter ip address 10.10.10.1 255.255.255.0 to assign an IP address to the 0/1 port using a 24-bit subnet
mask.
4. Enter no shutdown to activate the interface to pass data.
5. Enter exit to exit the Ethernet interface commands and return to the Global Configuration mode.
6. Enter ip route 0.0.0.0 0.0.0.0 10.10.10.254 to add a default route to the route table. 0.0.0.0 is the default
route and the default subnet mask, and 10.10.10.254 is the next-hop IP address to which the AOS unit
2
https://supportforums.adtran.com
OMMANDS
ONFIGURING THE
Total Access 900 Series Hardware Installation
for more details.
U ' IP A
NIT S DDRESS
64243916F1-13C