Notes For Timer Recording & One-Touch Timer Recording (Otr) - FUNAI CDV225FX4 Owner's Manual

Dvd / cd player with video cassette recorder
Table of Contents

Advertisement

3
Select "ONCE", "DAILY" (Mon-Fri) or "WEEKLY".
Then press [B] to go to next step.
or
4
Select the desired date.
Then press [B] to go to next step.
or
or
• You can program the Unit to record up to 8 programs, for up to
a year in advance.
5
Select the desired starting time (hour).
Then press [B] to go to next step.
or
or
Select "AM" or "PM".
6
Then press [B] to go to next step.
or
7
Repeat the procedure in steps 5 and 6 to set the ending time.
8
Select "L1" or "L2".
Then press [B] to go to next step.
or
Notes for Timer Recording & One-touch Timer Recording (OTR)
• If a cassette tape is not in the Unit or does not have the erasure prevention tab, TIMER REC indicator on this Unit blinks and timer
recording cannot be performed. Please insert a recordable cassette tape.
• When timer recordings are set, TIMER REC indicator on this Unit lights up. To use the VCR as usual, until the time for the recording,
press [TIMER SET] so that TIMER REC indicator light turns off.
After a one-touch timer recording or a timer recording has been set, this Unit operates as described below:
• If a cassette tape runs out before a one-touch timer recording or a timer recording is finished, the Unit ejects the cassette tape. Press
[TIMER SET] on the Remote Control or [STOP/EJECT C A] on the Unit, then press [VCR
• Once the Unit turns to the timer standby mode, no VCR functions are available until [TIMER SET] is pressed.
• To cancel the timer standby mode, press [TIMER SET] on the Remote Control or [STOP/EJECT C A] on the Unit, then press [VCR
to activate the VCR function again.
When an one-touch timer recording or a timer recording is completed...
• TIMER REC indicator on this Unit flashes if there are no more timer recordings on standby.
• The Unit goes to the DVD mode and all the VCR functions will be unavailable. All the DVD functions are available during one-touch
timer recording, timer standby mode and timer recording.
• Press [STOP/EJECT C A] on this Unit or [TIMER SET] on the Remote Control to use the VCR when the Unit is turned off.
• Press [SOURCE] on this Unit or [VCR
in standby mode, press [STOP/EJECT C A] on this Unit or [TIMER SET] on the Remote Control and then press [SOURCE] on this Unit
or [VCR
] on the Remote Control.
If you want to use the DVD player during a timer recording or while TIMER REC indicator on this Unit is on or blinking.
y
p y
Q Q
• Press [
] to turn on the Unit. Press [DVD
as described in this manual.
Note for timer recording:
If there is a power failure or the Unit is unplugged for more than 30 seconds, clock time setting and ALL timer programs will be lost.
When power is restored or Unit is plugged in again the clock and timer programs will need to be set up again.
EN
PROGRAM NUMBER 1
B ONCE
DAILY
WEEKLY
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 0 2 TUE
START
TIME – – : – –
END
TIME – – : – –
L1/L2
– –
REC
SPEED – –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 0 2 TUE
START
TIME 0 7 : 3 0
END
TIME – – : – –
L1/L2
– –
REC
SPEED – –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 0 2 TUE
UE
START
TIME 0 7 : 3 0
END
TIME – – : – –
L1/L2
– –
REC
SPEED – –
B PM
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 0 2 TUE
START
TIME 0 7 : 3 0
END
TIME 0 8 : 3 0
L1/L2
L1
REC
SPEED – –
g
g
g
g
] on the Remote Control to use the VCR when the Unit is turned on. In case timer recording is
g
g
] on the Remote Control to choose DVD mode, then continue with the other DVD features
9
Select recording speed.
Then press [CLEAR].
• To set another program after step 9, press [B].
Then continue with step 2.
10
Press [TIMER SET] to set the timer standby mode.
TIMER SET
– –
– –
• TIMER REC indicator on this Unit lights up and the Unit goes to
the DVD mode.
Note(s):
• To go back one step, press [s] during steps 3 to 9.
• Select "L1" to activate rear input jacks. Select "L2" to activate front input
jacks.
To check, correct or cancel a timer program
– –
– –
1) Press [TIMER SET] then, [VCR
2) Press [SETUP] to call up the main menu.
3) Select "TIMER PROGRAMMING" by using [ K / L], then press
[ B].
4) Select the program number which you want to check by
using [ K / L]. The details of the program you selected will
P
PM
appear on the TV screen.
– –
– –
• Go to the digit you want to change by using [s / B]. Then,
AM
enter correct numbers by using [ K / L].
• You may cancel the entire program by pressing [s] while
the program number blinks.
5) Press [CLEAR] to exit.
6) Press [TIMER SET] to return to the timer standby mode.
To cancel a timer recording in progress
PM
PM
Press [STOP/EJECT C A] on the Unit.
p
p
– 13 –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
START
END
CLEAR
L1/L2
REC
p g
] on the Remote Control.
g p g
] to activate the VCR function again.
g
Continued on next page.
1 0 / 0 2 TUE
TIME 0 7 : 3 0
PM
TIME 0 8 : 3 0
PM
L1
SPEED SP
B SP
SLP
]

Advertisement

Table of Contents
loading

Table of Contents