Related Manuals for Sizewise Advantage Bed
Summary of Contents for Sizewise Advantage Bed
- Page 1 Advantage Bed™ User Manual Doc. #8024, Rev. 7.0, Rev. Date: 2/26/2021 MFG-0020E-0420...
-
Page 2: Table Of Contents
Table of Contents Definition of Symbols ........................3 Manual Definitions ........................3 Warnings and Cautions ....................... 3 Important Safety Instructions ...................... 5 Device Information ......................... 9 Description of the SW Advantage™ ..................9 Specifications ..........................10 Unpacking and Set-Up Instructions ....................12 Unpacking/Parts Breakdown .................... - Page 3 General Safety ........................... 39 Pinch Point ..........................40 Transport ........................... 41 Cleaning Instructions ........................42 Laundry Instructions ......................... 45 Optional Accessories ........................ 46 Maintenance ..........................48 Fasteners ........................... 49 Storage and Disposal......................... 49 Troubleshooting ..........................50 Warranty Information ........................51...
-
Page 4: Definition Of Symbols
Definition of Symbols Manual Definitions Throughout this manual different type fonts and icons are used to aid user readability and understanding of the content. Below are some examples. Standard Text Used for regular information. Bold Face Text Emphasizes a word or phrase. SETS APART SPECIAL INFORMATION OR IMPORTANT NOTE INSTRUCTION CLARIFICATION. - Page 5 Symbol for Type B applied parts indicating protection provided against electric shock. The pinch point is spacing between movable parts of the device which, in The hazards and warnings are positions of normal use fail to maintain a indicated shipping clearance of ≤...
-
Page 6: Important Safety Instructions
Bed rail entrapment is a serious health risk that can result in serious injury or even death. Sizewise recommends the care provider be mindful of the FDA guidelines relevant to bed rail entrapment, as serious injury can result. These guidelines can be found on the FDA website. - Page 7 Bed rail entrapment is a serious health risk that can result in serious injury or even death. Sizewise recommends the care provider be mindful of the FDA guidelines relevant to bed rail entrapment, as serious injury can result. These guidelines can be found on the FDA website.
- Page 8 Bed rail entrapment is a serious health risk that can result in serious injury or even death. Sizewise recommends the care provider be mindful of the FDA guidelines relevant to bed rail entrapment, as serious injury can result. These guidelines can be found on the FDA website.
- Page 9 Many of the screws and bolts used in the bed are special high-strength fasteners. Contact an authorized Sizewise technician to assist if finding the correct fasteners. If improper fasteners are used, they could result in patient and/or user injury as well as damage to equipment or other property.
-
Page 10: Device Information
Device Information Description of the SW Advantage™ The SW Advantage™ is an electric bed. Its purpose is to assist the care provider by reducing the chance or fall or serious injury of individuals who require specialized positioning for their rehabilitation. The positioning nature of this bed also provides care providers the convenience in attending to the patients. -
Page 11: Specifications
Specifications Quality Assurance Standards ................IEC 60601 IEC/EN 60601-2-38 IEC/EN 60601-1 IEC 60601-1-2 Degree of Protection Against Electric Shock ............Type B Degree of Protection Against Ingress of Water ............IPX4 Electrical Rating.............(680 controller) 120VAC 60Hz, 4 amps (CO61 controller) 100-240VAC 50/60Hz Duty Cycle .........680/CO61 controller 2 Min ON / 18 Min OFF Cycle BA-16) 2 Min ON/ 18 Min OFF Cycle... - Page 12 Weight Capacity -Bed ................. 850 lbs. / 385 kg Optional IV Pole ..............50 lbs. / 22 kg Optional Trapeze ............850 lbs. / 385 kg (Exceeding these limits will void the warranty) With Optional Trapeze Attached to Bed Height from Floor ..............60.5” – 87.5” / 153.5 – 222 cm WARNING: Exceeding the weight capacity and/or safe working load listed in the specifications could result in patient or user injury as well as damage to equipment or other property.
-
Page 13: Unpacking And Set-Up Instructions
Unpacking and Set-Up Instructions Unpacking/Parts Breakdown Inspect for any signs of freight damage. If obvious damage is detected, contact the freight company and file a damage complaint. It may be necessary to take pictures of the damage. After visual inspection make sure all of the proper components have been received. Items enclosed in the main box: Headboard Footboard... -
Page 14: Bed Set-Up
Head and Footboards Bed Set-Up 1. Remove side rails and box before lifting 1 section off. Remove packaging wrapped around the items. After removing the 1 section of the bed, remove the head and footboards. Remove the 2 section of the bed from the pallet and proceed with assembling the bed. - Page 15 4. Locate the 3 – 5/8” bolts, washers and nuts. Place the bolt and washer together, then insert through the head section and then through the foot section of the bed. Add the washer and Nylock nut to complete the bed frame assembly.
- Page 16 7. Attach the foot control (optional) to the foot section of the bed. 8. Plug the bed into a 120V AC grounded outlet. At this point, the bed should be fully functional. Using the hand control, check the function of each button to make sure that the bed is functioning correctly.
-
Page 17: Headboard And Footboard Set-Up
Bed rail entrapment is a serious health risk that can result in serious injury or even death. Sizewise recommends the care provider be mindful of the FDA guidelines relevant to bed rail entrapment, as serious injury can result. -
Page 18: Operating Instructions
Operating Instructions Foot Controls The foot controls are located at the foot end of the bed. The controls have individual lock out functions as well as a master lock out switch. Locking out the specific function or all functions will disable the function on the hand control and foot controls. If a button is pushed while the function is locked out, a beep will sound for notification that an unauthorized operation has been selected. -
Page 19: Operation Of Bed
The buttons perform the following operations: A. Raises the head section B. Lowers the head section C. Raises the bed D. Lowers the bed E. Raises the foot F. Lowers the foot G. Trendelenburg (feet higher than head) H. Reverse Trendelenburg (head higher than feet) I. - Page 20 This bed is not intended for use in high moisture areas (e.g. showers, pool therapy), or extreme temperature environments. Use only parts, accessories and adapters authorized by the manufacturer. DO NOT use the bed with any unintentionally missing or abnormal parts. Remove the hand control when the patient is unattended.
-
Page 21: Proper Use Of The Bed
Proper Use of the Bed WARNING: Follow the instructions for assisting patients in and out of the bed to avoid a fall or injury to the patient and/or care provider. To get in the bed, position the bed at the proper height by following these steps: 1. -
Page 22: Side Rails
Bed rail entrapment is a serious health risk that can result in serious injury or even death. Sizewise recommends the care provider be mindful of the FDA guidelines relevant to bed rail entrapment, as serious injury can result. - Page 23 Provide help to the patient until he or she knows what can cause a slip or fall and how to avoid doing so. Never let the patient maneuver into or out of the bed without assistance until it is confirmed that the patient can do so safely. Position the bed at an elevation comfortable to the patient and/or care provider.
-
Page 24: Features
Features Casters The head and foot casters are both swivel and locking. The head section casters are also steering casters. To lock push down on the lever as indicated in the picture. To unlock the casters, lift up on lever. WARNING: While the patient is in the bed, it is recommended to lock the casters to reduce risk of injury to the patient and/or care provider. -
Page 25: Emergency Battery Backup (If Equipped)
Battery Backup In case of power failure the emergency battery backup will operate the bed. Use only in emergency situations, the battery backup is not designed for continuous use. The battery will recharge itself while the bed is plugged into a hospital grade or grounded outlet. New batteries, or batteries stored for a long time, may take more time to charge. - Page 26 BA-16 Lead Acid Features and Options: • Lead Acid Technology: Lead Acid • Output voltage: 24V DC • Max. discharge current: 5A • Charging Current: 300 mA/controlled by BA16 • Battery capacity: 1.3Ah/24V • Weight: 1545g • Housing colour: Light grey (RAL 7035) •...
- Page 27 UB1250 Battery Specifications: Nominal Voltage Rated Capacity (20 Hour Rate) Dimensions Length 3.54 in (89.9 mm) Width 2.74 in (70.1 mm) Height 3.98 in (101.1 mm) Total Height 4.21 in (106.9 mm) Approximate Weight 3.09 lbs. (1.4 kg) Battery Characteristics: Capacity* 20 Hour Rate (0.25A) 25°C (77°F)
-
Page 28: Serial Number Location
Serial Number Location The bed has a manufacturer serial number, and a Sizewise Rentals LLC serial number. The serial numbers are located at the foot of the bed. - Page 29 2. Slide wings onto deck. The wings should be placed on the deck so the mattress clip is on the bottom side of the wing. 3. Place end-plate on the ends of the wings. 4. Secure end-plate with the Self-Tapping Torx head screw using #30 Torx Bit.
-
Page 30: Iv Pole
Sizewise at 1-800-814-9389. WARNING: Do not attempt to install, repair, or remove the trapeze, single pole patient assist, or any other overhead components/devices while bed is occupied. WARNING: Before positioning patient on bed, verify all components are secure after adjustments, repairs, or servicing of the trapeze, single pole patient assist, or any other overhead components/devices. - Page 31 1. Attach the end posts into the appropriate brackets on the head and foot sections of the bed. 2. Place the overhead beam into the slots on top of each end post. NOTE: Be sure to place the holes facing upward on the overhead beam.
-
Page 32: Seven Zones Of Bed Rail Entrapment
If the patient would have any clinical conditions that could result in risk of falling or improperly lying in bed, the bed should be left at its lowest setting and in flat position when not attended. Sizewise recommends the use of bed rails if they are available. There are seven zones of bed rail entrapment. - Page 33 This bed complies with IEC 60601-2-38 standard for bed rail entrapment. Below are the specifications of that standard. This was taken from the 60601-2-38 Amend. 1 IEC 1999. DESIGNATOR DESCRIPTION DIMENSION Smallest dimension between elements inside ≤ 120 mm (4.72”) the perimeter of the SIDE RAIL in its raised/locked positions or perimeters created between the SIDE RAIL and fixed parts of...
-
Page 34: Safety Tips
Safety Tips Electrical Leakage Test Point CAUTION: If the ground is not properly connected to the electrical leakage test point a false reading may occur. In the event the electrical leakage test is done, the proper location for this test is on the main frame by the center joint on either side of the bed. - Page 35 Replacement parts, such as cables and accessories, must be purchased through Sizewise to ensure proper compliance requirements. WARNING: Using other manufacturer’s cables and accessories may affect EMC performance. Unauthorized use of these items will void warranty and could result in patient and/or user injury as well as damage to equipment or other property.
-
Page 36: Electromagnetic Interference (Emi) From Radio Wave Sources
The essential performance of this bed is to adjust the bed, using the hand control or foot control box, into various positions, such as bed up/down, head up/down, foot up/down, Trendelenburg and Reverse Trendelenburg with no interference. GUIDANCE AND MANUFACTURER’S DECLARATION Sizewise Manufacturing Company: 36060110, 36060100 - Advantage Bed Model: Control Number: 3107769... - Page 37 Guidance and Manufacturer’s Declaration – Emissions Equipment and Systems that are NOT Life-Supporting The SW Advantage™ is intended for use in the electromagnetic environment specified below. The customer, or user, of the bed should ensure that it is used in such an environment. Emissions Test Compliance Electromagnetic Environment Guidance RF Emissions...
- Page 38 Guidance and Manufacturer’s Declaration – Immunity All Equipment and Systems The SW Advantage™ is intended for use in the electromagnetic environment specified below. The customer, or user, of the SW Advantage™ should ensure that it is used in such an environment. Immunity Test IEC 60601 Compliance...
- Page 39 Guidance and Manufacturer’s Declaration – Immunity Equipment and Systems that are NOT Life-Supporting The SW Advantage™ is intended for use in the electromagnetic environment specified below. The customer, or user, of the bed should ensure that it is used in such an environment. Immunity Test IEC 60601 Compliance...
-
Page 40: General Safety
Recommended Separation Distances between portable and mobile RG Communications equipment and bed. Equipment and Systems that are NOT Life-Supporting Recommended Separation Distances for the SW Advantage™: The SW Advantage™ is intended for use in the electromagnetic environment in which radiated disturbances are controlled. -
Page 41: Pinch Point
Pinch Point Watch for pinch points on the bed, which are indicated by the pinch point label. HAZARD: Pay close attention to pinch points on the bed to avoid injury to the patient and/or care provider. Pinch points have minimal clearances between two moving parts that fail to maintain a clearance of ≤... -
Page 42: Transport
Transport During transport, use caution so the bed does not tip or WARNING: overbalance. Failure to do so could result in patient and/or user injury as well as damage to equipment or other property. The bed needs to be stored, transported and operated in a CAUTION: temperature range of -5°C to 45°C (23°F to 113°F). -
Page 43: Cleaning Instructions
Cleaning Instructions WARNING: Before cleaning the bed, be sure to disconnect it from the wall outlet (power source). Failure to do so could result in electrical shock and could result in patient and/or user injury as well as damage to equipment or other property. - Page 44 General Patient Room Cleaning/Disinfecting Personal Protective Equipment should always be used as directed by the Material Safety Data Sheet for the disinfectant. Prepare the disinfectant according to the manufacturer’s recommendations. Prepare a separate bucket of warm, fresh water to be used for rinsing the equipment after cleaning/disinfecting procedures are completed as instructed.
- Page 45 Steam Cleaning This product may be steam cleaned to eliminate bacteria and/or bed bug infestations, if desired. When applying steam, avoid areas such as electrical connections and components including scale meters, scale system components, hand and/or footboard controls that may be damaged by being exposed to excessive moisture and/or heat.
-
Page 46: Laundry Instructions
6. Allow the mattress to remain wet with disinfectant solution for the manufacturer’s recommended contact time. 7. Stains on the mattress may be treated using a mild stain remover, according to the manufacturer’s recommendations, using a soft bristled brush. 8. Rinse all surfaces of the mattress with fresh water and clean cloth to remove chemical and organic residue. -
Page 47: Optional Accessories
Air Therapy Internal Mattress Components 1. Prepare the disinfectant according to the manufacturer’s recommendations. 2. Prepare a separate bucket of warm, fresh water to be used for rinsing the equipment after cleaning/disinfecting procedures are completed as instructed. 3. Using a clean cloth dampened with the disinfectant solution, wipe all internal mattress surfaces, including the air cells, and allow to remain wet for the manufacturer’s recommended contact time. - Page 48 After cleaning, all surfaces are to be wiped with a clean, dry cloth to remove any moisture or residue. If necessary, the trapeze frame may be steam cleaned. Cleaning Blood and Other Excretions: Blood and other excretions should be wiped up while wet, if possible. These substances are more difficult to remove once they have dried to surfaces.
-
Page 49: Maintenance
Check the items on this chart at the indicated intervals. If any of the items are loose, worn, bent or distorted, immediately have them checked and/or repaired by an authorized Sizewise Technician. Frequent maintenance and servicing will improve performance between each use and extend bed life. -
Page 50: Fasteners
If improper fasteners are used, they could result in patient and/or user injury as well as damage to equipment or other property. Improper fasteners may fail. Use only screws and bolts provided by an authorized Sizewise representative. -
Page 51: Troubleshooting
On the Attendant Control Board: Simultaneously press the Master lock button and the CPR button and hold for 5 seconds. The lockout will release. NOTE: If the troubleshooting process does not solve the problem please contact a SizeWise representative for service. -
Page 52: Warranty Information
Product No. 36060110 & 36060100 Limited Product Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR SIZEWISE PRODUCT. BY USING THE PRODUCT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. LIMITED WARRANTY. - Page 53 This Limited Product Warranty shall not apply to, and Sizewise shall have no obligation to make repairs, replace or correct products including any part or parts of the product as the result of Sizewise’s determination of any of the following:...
- Page 54 (A) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN TORT, WHETHER OR NOT ARISING FROM THE NEGLIGENCE OF SIZEWISE OR ITS SUPPLIERS (WHETHER ACTIVE, PASSIVE OR IMPUTED); AND (B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY FOR LOSS OF OR DAMAGE TO ANY PRODUCT OR PART(S). THIS DISCLAIMER AND RELEASE SHALL APPLY EVEN IF THE EXPRESS WARRANTY SET FORTH ABOVE FAILS OF ITS ESSENTIAL PURPOSE.
- Page 55 Sizewise Advantage Bed Product No. 36060110 & 36060100 Limited Product Warranty To make a warranty claim, contact: Complete this portion and keep for your records. Manufacturing 36060110, 36060100- SW Advantage Limited Product Warranty D-L00-001...
- Page 56 Lenexa, KS 66215 800-814-9389 sizewise.com Sizewise is a registered trademark of Sizewise Rentals, LLC. All specifications, equipment, and prices are subject to change without notice. Photos and drawings are representative of the products and may vary slightly from actual production models.