Elatec TWN4 MULTITECH 2 M BLE Integration Manual
Hide thumbs
Also See for TWN4 MULTITECH 2 M BLE:
- User manual (60 pages) ,
- Manual (30 pages) ,
- Technical handbook (21 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Elatec TWN4 MULTITECH 2 M BLE
Summary of Contents for Elatec TWN4 MULTITECH 2 M BLE
- Page 1 TWN4 MULTITECH 2 M BLE TWN4 MultiTech 2 M INTEGRATION MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION .................................. 3 ABOUT THIS MANUAL ..............................3 ABOUT TWN4 MULTITECH 2 M BLE ..........................3 ELATEC SUPPORT ................................3 REVISION HISTORY ..............................3 SAFETY INFORMATION ..............................3 INTEGRATION INSTRUCTIONS ............................4 GENERAL ..................................4 LIST OF APPLICABLE RULES ............................4 SPECIFIC OPERATIONAL USE CONDITIONS ......................4 LIMITED MODULE PROCEDURES ..........................4... -
Page 3: Introduction
ABOUT TWN4 MULTITECH 2 M BLE The TWN4 MultiTech 2 M BLE reader module has integrated RFID (LF & HF) and Bluetooth Low Energy (BLE), which is supported by mobile phones with Android version 4.3 or greater, iOS 8.0 or greater and PCs with Windows (new Bluetooth hardware integrated). -
Page 4: Integration Instructions
GENERAL TWN4 MultiTech 2 M BLE may be installed in any host devices, as long as it is operated under the operational conditions stated in the user manual and other technical documents (e.g. data sheet). TWN4 MultiTech 2 M BLE is equipped with two integrated antennas. -
Page 5: Label And Compliance Information
ADDITIONAL TESTING, PART 15 SUBPART B DISCLAIMER TWN4 MultiTech 2 M BLE is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. -
Page 6: Mechanical Installation
The module can be fixed with four screws M2.5. 3.12 ELECTRICAL CONNECTION The module can be connected to the host with a DF11 connector. 3.13 PROGRAMMATION/SOFTWARE INTEGRATION © 2021 ELATEC GmbH – TWN4 MultiTech 2 M BLE integration manual DocRev2 – 07/2021 Page 6 of 10... -
Page 7: Compliance Statements
4 COMPLIANCE STATEMENTS TWN4 MultiTech 2 M BLE is in compliance with the EU directives and regulations as listed in the respective declaration of conformity. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 8: United Kingdom
Using a permanently affixed label, TWN4 MultiTech 2 M BLE must be labeled with its own FCC and IC identification numbers. In case this label is not visible anymore after integration of TWN4 MultiTech 2 M BLE in the host device, it is necessary to bring a label on the... -
Page 9: Appendix
Development Canada Apparatus (All Frequency Bands) For more information about this integration manual or TWN4 MultiTech 2 M BLE, go to www.elatec.com or contact ELATEC. © 2021 ELATEC GmbH – TWN4 MultiTech 2 M BLE integration manual DocRev2 – 07/2021... - Page 10 Elatec reserves the right to change any information or data in this document without prior notice. Elatec declines all responsibility for the use of this product with any other specification but the one mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own responsibility. Where application information is given, it is only advisory and does not form part of the specification.
Need help?
Do you have a question about the TWN4 MULTITECH 2 M BLE and is the answer not in the manual?
Questions and answers