Elatec TWN4 Quick Start Manual

Elatec TWN4 Quick Start Manual

Transponder reader
Hide thumbs Also See for TWN4:

Advertisement

Quick Links

Transponder Reader
TWN4 Mini Reader MIFARE NFC
Quick Start Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TWN4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Elatec TWN4

  • Page 1 Transponder Reader TWN4 Mini Reader MIFARE NFC Quick Start Guide...
  • Page 2: Technical Data

    - Short-circuit current < 8A Operating Temperature: -25 °C up to +80 °C 3. Getting Started 3.1 Cable Connection In order to start operating a TWN4 transponder reader, it simply has to be connected to a host. Page 2 of 12...
  • Page 3: Normal Operation

    Elatec GmbH 3.2 Enumeration (USB Only) This is only applicable for the USB version: Once the device has been powered up, it is waiting for completion of the enumeration by the USB host. As long as the device is not enumerated, it is entering a minimum power consumption mode.
  • Page 4 Elatec GmbH 3.6 Suspend Mode (USB Only) The USB version of the transponder reader supports the USB suspend mode. If the USB host is signaling suspend via the USB bus, the transponder reader is turning off most of its power consuming peripherals.
  • Page 5 Elatec GmbH 4. List of Antennas 13.56 MHz antenna Page 5 of 12...
  • Page 6: Compliance Statements

    Elatec GmbH 5. Compliance statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 7 Elatec GmbH RSS COMPLIANCE STATEMENT This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device Le présent appareil est conforme aux CNR d’Industrie Canada applicables...
  • Page 8 Elatec GmbH Labelling Requirements (Declaration of Conformity) Where the product is so small or for such use that it is not practicable to place the statement on it, the statement can be placed in a prominent location in the instruction manual.
  • Page 9 Elatec GmbH interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna.
  • Page 10 When additional application filing for RF exposure compliance demonstration is not required (e. g. if the TWN4 MultiTech 3 module in combination with all simultaneously operating transmitters complies with the RF exposure simultaneous transmission SAR test exclusion requirements), the host...
  • Page 11 Elatec GmbH If additional filing is required please contact the person at GMMC GmbH responsible for certification of the TWN4 MultiTech 3 module. NCC Warning Statement 低功率電波輻射性電機管理辦法 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得 擅自變更頻率、加大功率或變更原設計之特性及功能。 (即低功率電波輻射性電機管理辦法第十二條) 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現 象時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受 合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 (即低功率電波輻射性電機管理辦法第十四條) 本模組於取得認證後將依規定於模組本體標示審驗合格標籤, 並要求最終產品平台廠商(OEM Integrator)於最終產品平台(End Product)上標 示...
  • Page 12: Service Address

    Elatec GmbH 6. Service Address In case of any technical questions, please contact: Elatec GmbH Zeppelinstr. 1 82178 Puchheim Germany Phone: +49 (0) 89 5529961 0 Fax: +49 (0) 89 5529961 129 Email: info-rfid@elatec.com Page 12 of 12...

Table of Contents