Husqvarna 325iLK Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 325iLK
  6. Operator's manual

Husqvarna 325iLK Operator's Manual

Hide thumbs Also See for 325iLK:
Table of Contents

Advertisement

Quick Links

325iLK+TAB850
EN
Operator's manual
2-20

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 325iLK

Summary of Contents for Husqvarna 325iLK

  • Page 1 325iLK+TAB850 Operator's manual 2-20...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Troubleshooting............16 Safety................4 Transportation, storage and disposal......16 Assembly..............10 Technical data.............. 17 Operation..............12 Accessories..............18 Maintenance..............14 EC Declaration of Conformity........20 Introduction Intended use Note: National or local regulations can regulate the use. Comply to given regulations. Use the product with a trimmer head to cut different types of vegetation.
  • Page 3 The product can cause objects to eject, certification requirements for other commercial areas. which can cause injury. Manufacturer The product agrees with the applicable Husqvarna AB EC directives. Drottninggatan 2, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500 Product liability Use approved protective gloves.

  • Page 4: Safety

    • the product has an accessory that is not from the • the product is not repaired at an approved service manufacturer or not approved by the manufacturer. center or by an approved authority. Safety Safety definitions • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of Warnings, cautions and notes are used to point out electric shock.
  • Page 5 Power tool use and care • Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit • Do not force the power tool. Use the correct power unpredictable behavior resulting in fire, explosion or tool for your application.
  • Page 6 • Check that the product is in perfect working order. • Never use a product that is faulty. Carry out the Check that all nuts and screws are tight. safety checks, maintenance and service instructions described in this manual. Some maintenance and •...
  • Page 7 • Watch out for thrown objects. Always wear approved ANSI Z87.1 standard in the USA or EN 166 in EU eye protection. Never lean over the cut-ting countries. attachment guard. Stones, rubbish, etc., can be thrown up into the eyes which can cause blindness or serious injury.
  • Page 8 carried out correctly and if service and/or repairs are not carried out professionally. If you need further information please contact your nearest servicing dealer. WARNING: Never use a product with defective safety components. The product's safety equipment must be inspected and maintained as described in this section.
  • Page 9 To do a check of the cutting attachment guard • Remove the battery from the product before you assemble the product. WARNING: • Use approved protective gloves. Do not use a cutting • A defective or incorrect guard can cause injury. Do attachment without an approved and not use a cutting attachment that does not have an correctly attached cutting attachment guard.

  • Page 10: Assembly

    Assembly To assemble the loop handle 2. Align the tab (A) with the arrow (B) on the coupling. 1. Attach the loop handle onto the shaft between the arrows. Do not place loop handle or suspension ring on label. 3. Push the shaft into the coupling until it clicks into position.
  • Page 11 To disassemble the two-piece shaft To install the suspension ring if applicable 1. Install the suspension ring between the arrows on 1. Turn the knob 3 turns or more to loosen the the rear handle and the loop handle. coupling. Note: Do not put the loop handle on the decal.

  • Page 12: Operation

    Do the safety inspections, maintenance and servicing that are given in this manual. • Make sure that all covers, guards, handles and the WARNING: Only use Husqvarna cutting equipment are correctly attached and not original batteries with the product. damaged. •...
  • Page 13 To start the product Grass trimming with a trimmer head 1. Push and hold the start button until the green LED To trim the grass comes on. 1. Hold the trimmer head immediately above the ground at an angle. 2. Use the power trigger to control the speed. Do not push the grass trimmer line into the grass.

  • Page 14: Maintenance

    cord to prevent unbalance and vibrations in 2. Do not push the trimmer head to the ground. The ground and the product can be damaged. the handles. Also do a check of the other parts of the trimmer head and clean it if 3.
  • Page 15 Make sure that the bevel gear is filled correctly with grease, see bevel gear on page 15 . If not, use Husqvarna bevel gear grease. Do a check of the connections between the battery and the product. Do a check of the connection between the battery and the battery charger.

  • Page 16: Troubleshooting

    5. If the grease level is too low fill the bevel gear with Husqvarna bevel gear grease. Fill slowly and turn the drive shaft as you apply the bevel gear grease, stop at the correct level (B).

  • Page 17: Technical Data

    • Keep the battery away from the battery charger during storage. Do not let children and other not Technical data Technical data 325iLK together with TAB850 Motor Motor type BLDC (brushless) 36V Speed of output shaft, 1/min 5800...

  • Page 18: Accessories

    325iLK together with TAB850 Equipped with trimmer head (original) Vibration levels Vibration levels at handles, measured according to ISO 22867, m/s Equipped with trimmer head (original), left/right 3.6/1.4 Approved batteries Battery BLi 200 Type Lithium-ion Battery capacity, Ah Nominal voltage, V Weight, kg (lb) 1.3 (2.9)
  • Page 19 Attachments Approved attachments Attach- Attach- Use with ment ment number group Trimmer attachment TAB850 325iLK Brushcutter attachment BCA850 1-10 325iLK Blower attachment BA101 11-20 325iLK Edger attachment ECA850 21-30 325iLK Edger attachment ESA850 21-30 325iLK Hedge trimmer attachment HA860 31-40...

  • Page 20: Ec Declaration Of Conformity

    EC Declaration of conformity Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the battery grass trimmer Husqvarna 325iLK from 2019’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the requirements of the COUNCIL’S DIRECTIVES:...
  • Page 21 785 - 004 - 24.03.2021...
  • Page 22 785 - 004 - 24.03.2021...
  • Page 23 785 - 004 - 24.03.2021...
  • Page 24 Original instructions 114213026 2021-03-31...

This manual is also suitable for:

Tab850

Table of Contents