Husqvarna 325iLK+TAB850 Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 325iLK+TAB850
  6. Operator's manual

Husqvarna 325iLK+TAB850 Operator's Manual

Hide thumbs Also See for 325iLK+TAB850:
Table of Contents

Advertisement

Quick Links

Download this manual
325iLK+TAB850
EN
Operator's manual
2-20

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 325iLK+TAB850

Summary of Contents for Husqvarna 325iLK+TAB850

  • Page 1 325iLK+TAB850 Operator's manual 2-20...

  • Page 2: Table Of Contents

    Contents Introduction..............2 Troubleshooting............16 Safety................4 Transportation, storage and disposal......16 Assembly..............10 Technical data.............. 17 Operation..............12 Accessories..............18 Maintenance..............14 EC Declaration of Conformity........20 Introduction Intended use Only use the product with accessories that are approved Accessories on page 18 . by the manufacturer.
  • Page 3 Direct current. certification requirements for other commercial areas. Manufacturer The product can cause objects to eject, which can cause injury. Husqvarna AB Drottninggatan 2, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500 The product agrees with the applicable EC directives. Product liability...

  • Page 4: Safety

    • the product is not repaired at an approved service center or by an approved authority. Safety Safety definitions • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of Warnings, cautions and notes are used to point out electric shock.
  • Page 5 Power tool use and care • Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit • Do not force the power tool. Use the correct power unpredictable behaviour resulting in fire, explosion or tool for your application.
  • Page 6 • Check that the trimmer head and trimmer guard are described in this manual. Some maintenance and not damaged or cracked. Replace the trimmer head service measures must be carried out by trained and or trimmer guard if it has been exposed to impact or qualified specialists.
  • Page 7 attachment guard. Stones, rubbish, etc., can be ANSI Z87.1 standard in the USA or EN 166 in EU thrown up into the eyes which can cause blindness countries. or serious injury. • Listen out for warning signals or shouts when you wear hearing protection.
  • Page 8 carried out correctly and if service and/or repairs are not carried out professionally. If you need further information please contact your nearest servicing dealer. WARNING: Never use a product with defective safety components. The product's safety equipment must be inspected and maintained as described in this section.
  • Page 9 recommended cutting attachment guard for • Use approved protective gloves. the cutting attachment that you use, see • A defective or incorrect guard can cause injury. Do Accessories on page 18 . If an incorrect or not use a cutting attachment that does not have an faulty cutting attachment guard is attached approved guard attached.

  • Page 10: Assembly

    Assembly To assemble the loop handle 2. Align the tab (A) with the arrow (B) on the coupling. 1. Attach the loop handle onto the shaft between the arrows. Do not place loop handle or suspension ring on label. 3. Push the shaft into the coupling until it clicks into position.
  • Page 11 To disassemble the two-piece shaft To install the suspension ring if applicable 1. Install the suspension ring between the arrows on 1. Turn the knob 3 turns or more to loosen the the rear handle and the loop handle. coupling. Note: Do not put the loop handle on the decal.

  • Page 12: Operation

    Do the safety inspections, maintenance and servicing that are given in this manual. • Make sure that all covers, guards, handles and the WARNING: Only use Husqvarna original cutting equipment are correctly attached and not batteries with the product. damaged.
  • Page 13 To start the product Grass trimming with a trimmer head 1. Push and hold the start button until the green LED To trim the grass comes on. 1. Hold the trimmer head immediately above the ground at an angle. 2. Use the power trigger to control the speed. Do not push the grass trimmer line into the grass.

  • Page 14: Maintenance

    to prevent unbalance and vibrations in the 2. Do not push the trimmer head to the ground. The ground and the product can be damaged. handles. Also do a check of the other parts of the trimmer head and clean it if 3.
  • Page 15 The bevel gear is filled to ¾ with grease at the factory. Before use, make sure that the grease level has not changed. Use Husqvarna special grease if it is necessary to fill up. Do not change the grease in the bevel gear.

  • Page 16: Troubleshooting

    Troubleshooting Keypad LED display Possible faults Possible action Green activate LED flashing Low battery voltage. Charge the battery. Red error LED flashing Overload. The cutting attachment is jammed. deacti- vate the product. Remove the battery. Clean the cutting attachment from unwanted mate- rials.

  • Page 17: Technical Data

    Technical data Technical data 325iLK together with TAB850 Motor Motor type BLDC (brushless) 36V Speed of output shaft, 1/min 5800 Cutting width, mm Weight Weight without battery, kg Noise emissions Sound power level, measured dB (A) Sound power level, guaranteed L dB (A) Noise levels Equivalent sound pressure level at the operator's ear, measured according...

  • Page 18: Accessories

    Battery BLi 200 Weight, kg (lb) 1.3 (2.9) Approved battery chargers Battery charger QC330 Input voltage, V 100-240 Frequency, Hz 50-60 Power, W Accessories Accessories Approved accessories Accessory type Cutting attachment guard, art. Trimmer line Ø 2.0-2.4 mm Whisper twist trimmer line, maxi- mum Ø...
  • Page 19 Approved attachments Attach- Attach- Use with ment ment number group Polesaw attachment PAX730 41-50 325iLK Polesaw attachment PAX1100 41-50 325iLK Saw attachment PA1100 41-50 325iLK Clean sweep attachment SR600-2 51-60 325iLK Bristle brush attachment BR600 51-60 325iLK Dethatcher attachment DT600 51-60 325iLK Cultivator attachment CA230...

  • Page 20: Ec Declaration Of Conformity

    RISE SMP Svensk Maskinprovning AB,Box 7035, SE-750 07 Uppsala, Sweden, Box 7035, SE-750 07 Uppsala, Sweden, has performed voluntary type examination on behalf of Husqvarna AB. The certificate is numbered: SEC/19/2539 RISE SMP Svensk Maskinprovning AB has also verified agreement with appendix V of the council's directive 2000/14/EG.
  • Page 21 785 - 001 - 04.12.2019...
  • Page 22 785 - 001 - 04.12.2019...
  • Page 23 785 - 001 - 04.12.2019...
  • Page 24 Original instructions 1142130-26 2019-12-06...

Table of Contents