Table of Contents
Advertisement
Quick Links
CMS-1655 Central Monitoring Station
Installation and Programming Manual
LB-CMS1655-S
LB-CMS1655-T
Application
These installation instructions guide the installer through the installation of the CMS-1655 Central Monitoring Station.
Please read these instructions thoroughly before beginning installation.
North American Emissions Compliance
United States
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when this equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful
interference, in which case users will be required to correct the interference at their own expense.
Canada
This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du
Canada.
Installation
NOTICE
Risk of Property Damage.
Ensure that the power source conforms to the requirements of the equipment. Failure to use a correct power
source may result in permanent damage to the equipment.
NOTICE
Risque de dégâts matériels.
S'assurer que la source d'alimentation électrique est conforme aux spécifications de l'équipement. L'utilisation
d'une source d'alimentation électrique inappropriée risque d'endommager irrémédiablement l'équipement.
IMPORTANT: The CMS-1655 Central Monitoring Station must be wired to 24 VAC only. Wiring the unit
to 110 VAC will cause serious damange and void the warranty.
Use of the software that is in (or constitutes) this product or access to the cloud or hosted services applicable to
this product, if any, is subject to applicable terms set forth at www.johnsoncontrols.com/techterms. Your use of this
product constitutes an agreement to such terms. If you do not agree to be bound by such terms, you may return
the unused product to your place of purchase.
Refer to the QuickLIT website for the most up-to-date version of this document.
The Next Generation in Critical Airflow Controls
Code No. LIT-12013121, Rev. A
Issued August 2018
JCI FMS-1655
Advertisement
Table of Contents
Related Manuals for Johnson Controls CMS-1655
Summary of Contents for Johnson Controls CMS-1655
- Page 1 S’assurer que la source d’alimentation électrique est conforme aux spécifications de l’équipement. L’utilisation d’une source d’alimentation électrique inappropriée risque d’endommager irrémédiablement l’équipement. IMPORTANT: The CMS-1655 Central Monitoring Station must be wired to 24 VAC only. Wiring the unit to 110 VAC will cause serious damange and void the warranty.
-
Page 2: Table Of Contents
Quick Start Guide…………………………………………………...…………………………………………………………………………...…3 Main Display Screen...………………………………………...……………………………………………………………..…………………4 Configuring the CMS-1655..……………………………...……………………………………………………………..…………………4 Specifying Network Address(es)...…..…………………...……………………………………………………………..…………………5 Selecting Individual Parameters..………………………...……………………………………………………………..…………………5 Adding Password Security…………………………………...……………………………………………………………..…………………5 Changing Display Settings...………………………………...……………………………………………………………..…………………6 Wiring the CMS-1655 to Nearest JCI Controller....……………………………………………………………..…………………7 Notes....………………………………………...………..……………………………………………………..…………………8 PROGRAMMING MANUAL Introduction....……………..…………………………………………………………………………………………………………9 Main Setup Menu......………………………………………………………………………………………………………………………9 Unit Setup........……………………………………………………………………………………………………………………10 Configuring Monitor Settings..………………………………………………………………………………………………………………………10 Configuring Audible Alert Settings……………………………………………………………………………………………………………………11... - Page 3 INSTALLATION AND PROGRAMMING MANUAL Specifications CMS-1655 Central Monitoring Station Monitoring Capacity..…………………………………………........…….…Combination of any four FMS-1655 or HMS-1655 Interface Cable ……………….……………………………………………………………………………………………… Belden 3107A, 22 AWG minimum Protocol..……………………………………………………………………………………………………………..Protocol-independent (JCI proprietary) Power (may be supplied by FMS-1655 or by separate power supply)………………………………………………………………………… 18 to 32 Vdc Touchscreen User Interface LCD Size and Type..……………………………………………………………………………………………………………………...
-
Page 4: Installation Manual
• No separate power supply required and displaying parameters in any critical environment space or fume hood including The CMS-1655 is equipped with a 3.2” differential pressure, face velocity, isolation diagonal full-color touchscreen display in mode, operating mode, and alarm status. The portrait orientation (240 x 320 resolution). -
Page 5: Mounting Procedure: Surface Mount
1. The CMS-1655 flush thin mount model the mounting plate. For those applications should be mounted in a location that provides... -
Page 6: Quick Start Guide
INSTALLATION MANUAL motors, solenoids, contactors, and other electrical connections should be terminated 8. With power applied, the CMS-1655 should sources of induced noise. Use 22 AWG or before installing the cover with the display. display the offline status of four stations at the larger for all electrical wiring terminations. -
Page 7: Main Display Screen
INSTALLATION MANUAL SUBHEAD Quick Start Guide Main Display Screen supplemented by an audible alarm to indicate All CMS-1655 units come shipped from the that attention is required for the current factory in the Quad Station Monitor mode situation. (Figure 5). -
Page 8: Specifying Network Address(Es)
All password entries are stored in non-volatile Selecting Individual Parameters memory, and are preserved while the unit The CMS-1655 is capable of monitoring up is powered down. If a password has been to four parameters of up to four independent forgotten, there is a factory-default override JCI controllers. -
Page 9: Changing Display Settings
Display Setup >> Set Time & Date. The auto-dim feature of the Safety Halo™ The CMS-1655 is also designed to request function allows the CMS-1655 to go to a time and date settings periodically from any reduced intensity level (or even turn off... -
Page 10: Wiring The Cms-1655 To Nearest Jci Controller
INSTALLATION MANUAL Wiring CMS-1655 to Nearest FMS or HMS Controller Daisy chain together the SUB_NETs on the backplanes of all the FMS-1655 and/or HMS-1655 units that will be monitored by the CMS-1655. Connect the CMS-1655 to the SUB_NET and AUX_PWR terminals on the backplane of the... -
Page 11: Notes
INSTALLATION MANUAL Notes Due to continuous improvement, TRIATEK reserves the right to change product specifications without notice. Due to continuous improvement, JCI reserves the right to change product specifications without notice. -
Page 12: Programming Manual
All of the configuration screens that allow the option provides support for configuring all of button on the last screen to quickly exit the settings of the CMS-1655 to be configured for the display-specific settings integrated in the menu system and return to the main display. -
Page 13: Unit Setup
PROGRAMMING MANUAL SUBHEAD Unit Setup Configuring Monitor Settings The CMS-1655 is capable of monitoring and The Monitor Setup option on the Unit Setup displaying up to four parameters total, from up menu invokes the configuration screen shown to four individual JCI controllers. These four... -
Page 14: Configuring Audible Alert Settings
CMS-1655, and invokes the whenever an alarm condition occurs at one of an FMS-1655 configured for single sensor configuration screen shown in Figure 18 when the monitored stations or controllers. -
Page 15: System Setup
All of the configuration settings associated requirements of a specific application. This with the CMS-1655 alarm facility may be includes the ability to enable and disable accessed at the Alarms Setup menu shown individual alarms for both audible and visual in Figure 22. -
Page 16: Managing System Security Passwords
When Auto Clean mode at a monitored FMS- sections below. 1655 is enabled, the CMS-1655 indicates the status by a cyan background and a simulated Normal status indicates that the monitored fan as the action icon. The Safety Halo™... -
Page 17: Deleting An Existing Password
Safety Halo™ Settings for configuring all of the display settings on screen where the starting and ending hours of the CMS-1655. This includes configuring the the Dimmed Period may be specified. Safety Halo™ settings, selecting the display mode based on the number of parameters For example, to configure the Safety Halo™... -
Page 18: Setting System Time And Date
Setting System Time and Date After entering the digits for the current time, The Diagnostics menu provides support The CMS-1655 is designed to synchronize its tap the A/P button to specify am or pm, and for displaying information specific to this local time and date with the network-resident then tap the Next button to enter the date. -
Page 19: Resetting The Cms-1655
(subnetwork address). Selecting this option invokes the warning message as shown in Figure 31, informing the user that the CMS-1655 will be reset when the OK button is tapped to confirm the request. Due to continuous improvement, JCI reserves the right to change product specifications without notice. -
Page 20: User Menu Flow Diagram
PROGRAMMING MANUAL User Menu Flow Diagram Due to continuous improvement, JCI reserves the right to change product specifications without notice. - Page 21 CMS-1655 Central Monitoring Station Installation and Programming Manual LB-CMS1655-S Code No. LIT-12013121, Rev. A LB-CMS1655-T Issued August 2018 Refer to the QuickLIT website for the most up-to-date version of this document. +1-414-524-1200 Johnson Controls 5757 N. Green Bay Ave. P.O. Box 591...