i3 International S81 User Manual page 124

Action Indicates the classification action taken on ingress frame if parameters configured are matched
Modification Buttons with the frame's content.There are three action fields:
Port Members
Class: Classified QoS Class; if a frame matches the QCE it will be put in the queue.
Key Parameters
DPL: Drop Precedence Level; if a frame matches the QCE then DP level will set to value
displayed under DPL column.
DSCP: If a frame matches the QCE then DSCP will be classified with the value displayed under
DSCP column.
Each QCE can be modified using the following buttons
Check the checkbox button to made any port member of the QCL entry By default all ports will be
checked.
Key configuration are described as below:
Tag Value of Tag field ccna be 'Any', 'Untag' or 'Tag'
VID Valid value of VLAN ID can be any value in the range 1-ro95 or 'Any' user can enter either a
specific value or a range of VIDs.
PCP Priority Code Point: Valid value PCP are specific (0, 1, 2, 3, 4, 5, 6, 7, ) or range (0-1, 2-3, 4-5,
6-7, 0-3, 4-7, ) or 'Any'.
DEI Drop Eligible Indicator: Valid value of DEI can be 0, 1, or 'Any'
SMAC Source MAC address: 24 MS bits (OUI or 'Any').
DMAC Type Destination MAC Type: Possible vaules are unicast (UC), multicast (MC), broadcast (BC)
or 'Any'.
Frame Type: This can have any of the following values
: Inserts a new QCE before the current row.
: Edits the QCE.
& moves the QCE up or down the list.
: Deletes the QCE.
: The lowest plus sign adds a new entry at the bottom of the QCE listings.
1. Any: Allows all types of frames.
2. Ethernet: Valid Ethernet type can have a value within 0x6000-OxFFFF or 'Any', default
value is 'Any'
3. LLC: SSAP Address valid SSAP (Sorce Service Access point) can very from 0x00 to 0xFF
or 'Any'. DSAP Address Valid DSAP(Destination Service Access Point) can vary from 0x00
to 0xFF or 'Any', the default value is 'Any'.
Control Address Valid Control Address can vary from 0x00 to 0xFF or 'Any', the default
value is 'Any'.
4. SNAP: PID Valid PID(a.k.a Ethernet type) can have value within 0x00-0xFFFF or 'Any',
default value is 'Any'.
5. IPv4: Protocol IP protocol number: (0-255, TCP or UDP) or 'Any' Source IP Specific Source
IP address in value/mask format or 'Any'. IP and Mask are in the format x.y.z.w where x,
y, z, and w are decimal numbers between 0 and 255. When Mask is converted to a 32-bit
binary string and read from left to right, all bits following the first zero must also be zero
DSCP Diffserv Code Point value (DSCP): It can be specific value, range of value or 'Any'.
DSCP values are in the range 0-63 including BE, CS1-CS7, EF or AF11-AF43. IP Fragment
IPv4 frame fragmented option: yes|no|any. Sport Source TCP/UDP port:(0-65535) or 'Any',
specific or port range applicable for IP protocol UDP/TCP. Dport Destination TCP/UDP
port:(0-65535) or 'Any', specific or port range applicable for IP protocol UDP/TCP.
6. IPv6: Protocol IP protocol number: (0-255, TCP or UDP) or 'Any' Source IP IPv6 source
address: (a.b.c.d) or 'Any', 32 LS bits DSCP Diffserv Code Point value (DSCP): It can be
specific value, range of value or 'Any'. DSCP values are in the range 0-63 including BE,
CS1-CS7, EF or AF11-AF43. Sport Source TCP/UDP port:(0-65535) or 'Any', specific or
port range applicable for IP protocol UDP/TCP. Dport Destination TCP/UDP port:(0-65535)
or 'Any', specific or port range applicable for IP protocol UDP/TCP.
123