Table of Contents
Advertisement
12.1 Operating additional units
12.1.1 Additional cordless handsets
Up to 6 cordless handsets can be registered to a single
base unit. Additional cordless handsets will give you the
freedom to, for example, have an intercom call with
another cordless handset while a third cordless handset
is on an outside call.
Important:
R The additional cordless handset model
recommended for use with this unit is noted on
page 7.
12.2 Registering a cordless
handset to a base unit
The supplied cordless handset and base unit are
pre-registered. If for some reason the cordless handset
is not registered to the base unit, re-register the cordless
handset.
After purchasing an additional cordless handset, register
it to the base unit. Ensure that the additional cordless
handset is turned ON. Make sure that the batteries are
installed correctly (page 19).
1
MMENUN (soft key) A M#NM1NM3NM0N
2
Press and hold MLocatorN on the base unit for about
5 seconds, until the registration tone sounds.
R If all registered cordless handsets start ringing,
press the same button to stop. Then repeat this
step.
R After pressing MLocatorN, the rest of this
procedure must be completed within 90 seconds.
3
Press MOKN (soft key), then wait until a long beep
sounds.
Note:
R Charge the batteries of your additional cordless
handset for about 7 hours before initial use.
R While registering, "In use" is displayed on all
registered cordless handsets.
R When you purchase an additional cordless handset,
refer to the additional cordless handset's installation
manual for registration.
12.2.1 Deregistering a cordless handset
A cordless handset can cancel its own registration to the
base unit, or other cordless handsets registered to the
same base unit. This allows the cordless handset to end
its wireless connection with the system.
1
MMENUN (soft key) A M#NM1NM3NM1N
R All cordless handsets registered to the base unit
are displayed.
2
Select the cordless handset you want to cancel.
A MSELECTN (soft key)
12. Multi-unit Operation (KX-MB2060 optional)
3
"Yes" A MSELECTN (soft key)
4
MOFFN
12.3 Intercom
Intercom calls can be made between a cordless handset
and the base unit, and between 2 cordless handsets. You
can page all cordless handsets at once from the base
unit.
Note:
R If you receive an outside call while talking on the
intercom, you hear 2 tones. To answer the call, hang
up the intercom, then answer the outside call.
– see step 3 on "6.1.1 With the base unit",
page 49.
– see step 3 on "6.1.2 With the cordless handset
(KX-MB2060 optional)", page 49.
MFlashN / MFLASHN cannot be used to answer
outside calls.
R When paging the cordless handset, the paged
cordless handset beeps for 1 minute.
12.3.1 Making intercom calls
With the cordless handset
1. MMENUN (soft key) A MINTN (soft key)
2. To page the base unit, press M0N.
To page another cordless handset, press MCN or
MDN repeatedly to select the desired cordless
handset. A MSELECTN (soft key)
R The base unit or the destination cordless handset
will beep (be paged) for 1 minute.
R To stop paging, press MOFFN.
3. When the paged party answers, talk into the cordless
handset.
4. To end the intercom call, press MOFFN.
With the base unit
1. MIntercomN
2. To page one cordless handset, press the desired
cordless handset number.
To page all cordless handsets, press M0N.
R The destination cordless handset(s) will beep (be
paged) for 1 minute.
R To stop paging, press MMonitorN or MIntercomN.
3. When the paged party answers, lift the handset, and
talk to the other party.
4. To end the intercom call, replace the handset.
Cordless handset locator
You can locate a misplaced cordless handset by
pressing MLocatorNM0N on the base unit.
R All registered cordless handsets beep for 1 minute.
To stop paging, press MLocatorN again.
103
Advertisement
Table of Contents
