Features And Parts List; Loading The Dispenser - GE GXCC01DLGR Owner's Manual

Using the water dispenser.
GXCF05D
Floor model
GXCF20E/GXCF20FBB
Chiller model
4
GXCC01D
Countertop model
Loading the Dispenser and Start Up
Sanitize the dispenser water tanks prior to
installing a full bottle of water for the first
time (see "Cleaning and Sanitizing the
Water Tanks").
IMPORTANT: Make sure the dispenser is
unplugged with both the hot and cold power
switches (on the back of the dispenser, on
models so equipped) set to the O (off) position.
Before placing the water bottle on the
dispenser, wash hands and wipe the top of the
bottle with a clean cloth. Avoid touching the
part of the bottle that will be in contact with the
water dispenser.
Make sure the water level in the top of the
dispenser is low enough to allow for proper
bottle installation. Failure to do so may cause
the dispenser to overflow.
1. Peel the label from the top cover of the
bottle (if present). Do not remove the
entire bottle cap.

Features and Parts List

Bottle Support Collar (WS28X10047), grey for models
GXCF05D and GXCC01D
Bottle Support Collar (WS28X10049), white for model
GXCF20E, (WS28X10048) black for model GXCF20FBB
Separator (WS28X10013)
Cold Water Tank
Hot (Red) and Cold (Blue) Power Switches (back of
dispenser). The Cold (Blue) power switch also turns
on the chiller compartment (on model GXCF20E).
Indicator Lights. The green light will be lit when the
dispenser is plugged in. The red and blue lights will
cycle on and off while the dispenser heats and cools
water. Compressor start delayed by up to 3 minutes.
Hot (Red) and Cold (Blue) Water Dispenser Buttons
Dispenser Drip Tray (WS28X10016) and Grille
(WS28X10015), grey for models GXCF05D and GXCC01D
Dispenser Drip Tray (WS28X10026) and Grille
(SW28X10027) white for model GXCF20E
Dispenser Drip Tray (WS28X10031) and Grille
(WS28X10034) black for model GXCF20FBB
Compartment Tray (model GXCF20E/GXCF20FBB only)
(WS29X10029)
Storage Compartment (GXCF05D). Do not use to store
foods requiring refrigeration. The compartment is
not refrigerated.
Chiller Compartment (GXCF20E). The compartment
is intended solely for use in chilling canned and
boxed beverages, and packaged nonperishables.
Compartment Shelf (WS28X10028)
Drainage Cap (floor and chiller models) (WS01X10008)
Silicon Stopper (floor and chiller models) (WS01X10007)
Retaining Clip (countertop models) (WS01X10010)
Rubber Drain Cover (countertop models) (WS01X10011)
2. Place the bottle on top of the dispenser
as shown, aligning the dispensing valve
probe to the center of the water bottle
cap. Press down until the probe
penetrates the bottle cap, allowing the
bottle to rest on the support collar.
3. IMPORTANT: Press both dispense buttons
until water runs from both taps.
4. Plug in the dispenser.
5. Set the COLD and HOT power switches
(located on the top left rear of the
dispenser, on models so equipped) to
the I (on) position.
6. Allow 30 minutes for water to reach hot
and cold temperatures.
Contact a local water bottle distributor to
purchase water bottles.