Erasing Punch Noise (Erasepunchnoise); Erase A Silent Region (Erasesilence) - Korg D32XD Upgrade Manual

(2)
(3) Select the number of the track from which you want to
remove noise.
•For this example, set the Destination cell to track "1".
•Check the IN and OUT locations. If you want to set the
locations with more precision, press the Learn Noise
Wave button, and use the Wave dialog box (
p.139) to set the location.
•Check the TO and END locations. If you want to set the
locations with more precision, press the Destination
Wave button, and use the Wave dialog box (
p.139) to set the location.
(4) Execute the editing operation.
Press the Exec. button. In the NoiseReduction dialog box
that appears, press the Yes button to execute the opera-
tion.
When the operation is finished, the display will indicate
"Completed." Press the OK button.
(5) Verify the results of the operation.
Press the LOC3/TO key, and play back from the TO point.
If necessary, you can use Undo to return to the state prior
to applying the NoiseReduction (
This editing operation will take longer to complete depending on
the length of the TO-END region you that you specified.
The Destination can be set to the following choices.
D32XD
D16XD
ML and MR are master track L and R
For a 96 kHz/24-bit song, you can choose only up to tracks 1-8.
For D32XD 48 kHz/24-bit or 44.1 kHz/24-bit songs, only
tracks 1-16 can be selected.

Erasing punch noise (ErasePunchNoise)

Erasing noise from the IN-OUT region of track 1
(1) Specify the region where you want to erase punch noise.
Set the locations as follows (
•Set the IN location to a point slightly earlier than where
the noise occurs.
•Set the OUT location to a point after the noise.
(2) Select "ErasePunchNoise."
In the TRACK, "EditTrk" tab page, press the Edit Trk
Type cell. In the Edit Trk Type dialog box, select
"ErasePunchNoise" and press the OK button.
(2)
(3)
(4)
Manual:
→
Manual:
→
Manual: p.147).
→
[1...32, ML, MR]
[1...16, ML, MR]
Manual: p.69).
→
(3)
(3) Select the number of the track from which you want to
erase noise.
•For this example, set the Destination cell to track "1".
•Check the IN and OUT locations. If you want to set the
locations with more precision, press the Destination
Wave button, and use the Wave dialog box (
p.139) to set the location.
For the rest of the procedure, refer to step (5) and following
of "Erasing noise" ( Manual: p.74). For an overall explana-
→
tion of ErasePunchNoise, refer to the Reference section Op-
timize Trk A3.Mode "Erase Punch Noise" (
If this does not erase the noise, use Undo to return to the previ-
ous state, press the Mode button, and raise the "ErasePunchNoise
Sens" value slightly (→Manual: p.143).

Erase a silent region (EraseSilence)

Erasing regions of silent audio data from the IN-OUT
region of track 1, converting them to usable space on
the hard drive
(1) Specify the region of silence you want to erase.
Set the locations as follows (
•Set the IN location to a point slightly earlier than the
region of silence that you want to erase.
•Set the OUT location to the point after the region of si-
lence.
(2) Select "EraseSilence."
In the TRACK, "EditTrk" tab page, press the Edit Trk
Type cell. In the Edit Trk Type dialog box, select
"EraseSilence" and press the OK button.
(3) Select the number of the track from which you want to
erase silence.
•For this example, set the Destination cell to track "1".
•Check the IN and OUT locations. If you want to set the
locations with more precision, press the Destination
Wave button, and use the Wave dialog box (
p.139) to set the location.
(2)
For the rest of the procedure, refer to step (5) and following
of "Erasing region of silent audio data" (
For an overall explanation of ErasePunchNoise, refer to the
Reference section Optimize Trk A3.Mode "Erase Silence"
( Manual: p.142).
→
Manual:
→
Manual: p.143).
→
Manual: p.69).
→
Manual:
→
(3)
Manual: p.74).
→
Upgrade
Guide
5