Table of Contents
Advertisement
D2F
PCB Mounting Dimensions
(Reference)
5.8 ± 0.15
5.08 ± 0.1
12.8 ± 0.15
Dimensions and Operating Characteristics
Note: 1. All units are in millimeters unless otherwise indicated.
2. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
3. The following illustrations and drawings are for D2F models with PCB terminals. Self-clinching, solder, and right-angled, left-angled
terminals are omitted from the following drawings. Refer to page 200 for these terminals. When ordering, replace j with the code for
the terminal that you need.
4. The operating characteristics are for operation in the A direction ( ).
Pin Plunger Models
D2Fj
D2F-01j
D2F-Fj
D2F-01Fj
Hinge Lever Models
D2F-Lj
D2F-01Lj
D2F-FLj
D2F-01FLj
Simulated Roller Lever Models
D2F-L3j
D2F-01L3j
D2F-FL3j
D2F-01FL3j
2.54
2.54
Three,
1.2 dia. holes
12.7
1.2
5.2
+0.12
A
2.2
dia.
0
+0.12
2
0
6.5±0.1
3.15
5.08
5.08
12.8±0.15
12.8
(10.8)
A
t = 0.3 (see note)
OP
Note: Stainless-steel lever
12.7
(7.5)
A
2.1
10
1.3R
Note: Stainless-steel lever
Mounting Holes
Two , 2-dia. mounting holes
6.5 ± 0.15
5.7
PT
+0.12
2.9
OF max.
2
dia. holes
0
RF min.
PT max.
5
OP
OT min.
1.5
MD max.
3.5
OP
0.4
0.9
5.8±0.15
OF max.
3
RF min.
OT min.
FP
MD max.
FP max.
OP
OF max.
t = 0.3 (see note)
3
RF min.
OT min.
FP
MD max.
OP
FP max.
OP
Model
D2Fj
D2F-01j
D2F-01Fj
1.47 N {150 gf}
{
g }
0.74 N {75 gf}
0.20 N {20 gf}
0.05 N {5 gf}
0.5 mm
0.25 mm
0.12 mm
5.5±0.3 mm
Model
D2F-Lj
D2F-01Lj
D2F-01FLj
0.78 N {80 gf}
{
g }
0.25 N {25 gf}
0.05 N {5 gf}
0.02 N {2 gf}
0.55 mm
0.5 mm
10 mm
6.8±1.5 mm
Model
D2F-L3j
D2F-FL3j
D2F-01L3j
D2F-01FL3j
0.78 N {80 gf}
{
g }
0.39 N {40 gf}
0.05 N {5 gf}
0.02 N {2 gf}
0.5 mm
0.45 mm
13 mm
8.5±1.2 mm
D2F
D2F-Fj
{
g }
D2F-FLj
{
g }
{
g }
201
Advertisement
Table of Contents
