Advertisement
List of Options
Shield Cable with 50-Pin Mini-Ribbon Connectors
at either Ends
Shield Cable with 50-Pin Mini-Ribbon Connector
at one End
Screw Terminal Unit (M3 x 50P)
Buffer Amplifier Box for Analog Input Boards
(8ch type)
Buffer Amplifier Box for Analog Input Boards
(16ch type)
BNC Terminal Unit
(for analog input 8ch)
*1 PCB50PS-0.5P or PCB50PS-1.5P optional cable is required separately.
*2 "Spring-up" type terminal is used to prevent terminal screws from falling off.
*3 An external power supply is necessary (optional AC adaptor POA200-20 prepared.)
*4 Capable of using the analog input of up to 8ch, and analog output of up to 2ch.
* Check the CONTEC's Web site for more information on these options.
How to connect the connectors
Connector shape
To connect an external device to this board, plug the cable from the
device into the interface connector (CN1) shown below.
Interface connector (CN1)
Connector Pin Assignment
Pin Assignments of AIO-160802LI-PE Interface Connector (CN1)
Non Connect
N.C.
50
Analog Ground ( for AO )
AGND
49
Non Connect
N.C.
48
Analog Ground ( for AO )
AGND
47
Analog Input 04
AI 04
46
50
Non Connect
N.C.
45
Analog Input 05
AI 05
44
Non Connect
N.C.
43
Analog Ground ( for AI )
AGND
42
Analog Ground ( for AI )
AGND
41
Analog Input 06
AI 06
40
Non Connect
N.C.
39
Analog Input 07
AI 07
38
Non Connect
N.C.
37
AO External Start Trigger AO START 36
AO External Stop Trigger AO STOP
35
AO External Sampling Clock AO EXCLK 34
Digital Ground
DGND
33
Digital Output 00
DO 00
32
26
Digital Output 01
DO 01
31
Digital Output 02
DO 02
30
Digital Output 03
DO 03
29
Digital Ground
DGND
28
Counter UP Clock Input
CNT
27
Reserved
Reserved
26
Analog Input00 - Analog
Analog input signal. The numbers correspond to channel numbers.
Input07
Analog Output00 - Analog
Analog output signal. The numbers correspond to channel numbers.
Output01
Analog Ground
Common analog ground for analog I/O signals.
AI External Start Trigger
External trigger input for starting analog input sampling.
Input
AI External Stop Trigger
External trigger input for stopping analog input sampling.
Input
AIO-160802LI-PE
PLUG-IN Electronic GmbH • Am Sonnenlicht 5 • 82239 Alling • Tel.: +49 (0) 8141 3697-0 • info@plug-in.de • www.plug-in.de
:PCB50PS-0.5P (0.5m)
:PCB50PS-1.5P (1.5m)
:PCA50PS-0.5P (0.5m)
:PCA50PS-1.5P (1.5m)
:EPD-50A *1*2
:ATBA-8L *1*3
:ATBA-16L *1*3
:ATP-8L *1*4
- Connector used
50-pin mini-ribbon connector
10250-52A2JL[mfd.by 3M]
-
Compatible
connector
10150-6000EL[mfd. by 3M]
CN1
25 AO 00
Analog Output 00
24 AGND
Analog Ground ( for AO )
23 AO 01
Analog Output 01
22 AGND
Analog Ground ( for AO )
21 AI 00
Analog Input 00
25
20 N.C.
Non Connect
19 AI 01
Analog Input 01
18 N.C.
Non Connect
17 AGND
Analog Ground ( for AI )
16 AGND
Analog Ground ( for AI )
15 AI 02
Analog Input 02
14 N.C.
Non Connect
13 AI 03
Analog Input 03
12 N.C.
Non Connect
11 AI START AI External Start Trigger
10 AI STOP AI External Stop Trigger
9 AI EXCLK AI External Sampling Clock
8 DGND
Digital Ground
7 DI 00
Digital Input 00
1
6 DI 01
Digital Input 01
5 DI 02
Digital Input 02
4 DI 03
Digital Input 03
3 DGND
Digital Ground
2 CNT
Counter Gate Control Input
1 CNT OUT Counter Output
AI External Sampling Clock
External sampling clock input for analog input.
Input
AO External Start Trigger
External trigger input for starting analog output sampling.
Input
AO External Stop Trigger
External trigger input for stopping analog output sampling.
Input
AO External Sampling Clock
External sampling clock input for analog output.
Input
Digital Input00 - Digital
Digital input signal.
Input03
Digital Output00 - Digital
Digital output signal.
Output03
Counter Gate Control Input Gate control input signal for counter .
Counter Up Clock Input
Count-up clock input signal for counter .
Counter Output
Counter output signal.
Digital Ground
Common digital ground for digital I/O signals, external trigger inputs, external sampling
clock inputs, and counter I/O signals.
Reserved
Reserved pin.
N.C.
No connection to this pin.
CAUTION
-
Do not connect any of the outputs and power outputs to the analog or digital ground.
Neither connect outputs to each other. Doing either can result in a fault.
-
If analog and digital ground are shorted together , noise on the digital signals may affect the
analog signals. Accordingly, analog and digital ground should be separated.
-
Leave "Reserved" pins unconnected. Connecting these pins may cause a fault in the board.
Analog Input Signal Connection
Single-ended Input
The following figure shows an example of flat cable connection.
Connect separate signal and ground wires for each analog input
channel on CN1.
Single-ended Input Connection (Flat Cable)
BOARD
CN1
Analog Input 0..15*1
Analog Ground
The following figure shows an example of shield cable connection. Use
shielded cable if the distance between the signal source and board is
long or if you want to provide better protection from noise. For each
analog input channel on CN1, connect the core wire to the signal line
and connect the shielding to ground.
Single-ended Input Connection (Shield Cable)
BOARD
CN1
Analog Input 0..15*1
Analog Ground
*1 The number of channels depends on each board. The AIO-160802LI-PE has eight channels.
CAUTION
-
If the signal source contains over 1MHz signals, the signal may effect the cross-talk noise
between channels.
-
If the board and the signal source receive noise or the distance between the board and the
signal source is too long, data may not be input properly.
-
An input analog signal should not exceed the maximum input voltage (relate to the board
analog ground). If it exceeds the maximum voltage, the board may be damaged.
-
Connect all the unused analog input channels to analog ground.
-
The signal connected to an input pin may fluctuate after switching of the multiplexer. If this
occurs, shorten the cable between the signal source and the analog input pin or insert a high-
speed amplifier as a buffer between the two to reduce the fluctuation.
-
Analog ground of CN1 is isolated from the ground in the PC.
Analog Output Signal Connection
This section shows how to connect the analog output signal by using a
flat cable or a shielded cable.
The following figure shows an example of flat cable connection.
Connect the signal source and ground to the CN1 analog output.
Analog Output Connection (Flat Cable)
CN1
BOARD
Analog Output 0..3*2
Analog Ground
Ver.1.05
Cable
Signal Source
Shield cable
Signal Source
Cable
Target
3
Advertisement
