HIKVISION TURBO HD DS-2CE56D8T-IRS User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. TURBO HD DS-2CE56D8T-IRS
  6. User manual
HIKVISION TURBO HD DS-2CE56D8T-IRS User Manual

HIKVISION TURBO HD DS-2CE56D8T-IRS User Manual

2 mp cube camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TURBO HD
2 MP Cube Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the models below:
Model
DS-2CE56D8T-IRS
This manual may contain technical incorrect places or
printing errors, and the content is subject to change
without notice. The updates will be added to the new
version of this manual. We will readily improve or
update the products or procedures described in the
manual.
0100001070705

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION TURBO HD DS-2CE56D8T-IRS

Summary of Contents for HIKVISION TURBO HD DS-2CE56D8T-IRS

  • Page 1 TURBO HD 2 MP Cube Camera User Manual User Manual Thank you for purchasing our product. If there are any questions, or requests, do not hesitate to contact the dealer. This manual applies to the models below: Model DS-2CE56D8T-IRS This manual may contain technical incorrect places or printing errors, and the content is subject to change without notice.
  • Page 2 Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
  • Page 3 Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions”. Warnings: Serious injury or death may occur if any of the warnings are neglected.
  • Page 4 Keep the camera away from liquid while in use for  non-water-proof device. While in delivery, the camera shall be packed in its  original packing, or packing of the same texture. Mark Description Table 0-1 Mark Description Mark Description DC Voltage...
  • Page 5 1 Introduction 1.1 Product Features The camera is applicable for indoor conditions, and the application scenarios include office, store, living room, etc.. The main features are as follows: High performance CMOS sensor  Low illumination, 0.005 Lux @ (F1.2, AGC ON), 0 Lux ...

  • Page 6: Installation Preparation

    2 Installation 2.1 Installation Preparation Before you start: Make sure that the device in the package is in good  condition and all the assembly parts are included. Make sure that all the related equipment is power-off  during the installation. Check the specification of the products for the ...
  • Page 7 Disassemble the 3-axis bracket. (1) Hold the base with one hand. (2) Rotate the pole anticlockwise to disassemble the pole from the base. Disassemble the Bracket Install the fixed tray to the ceiling with supplied screws. Install the base to the fixed tray. Install the Mounting Base to the Fixed Tray Install the camera to the bracket.

  • Page 8: Menu Description

    3 Menu Description Purpose: Call the menu by clicking icon on the PTZ Control interface, or call preset No.95. Steps: 1. Connect the camera with the TVI DVR, and the monitor, shown as the figure 3-1. TVI DVR Camera Monitor Connection 2.

  • Page 9: Exposure Mode

    3.2 LANGUAGE Supports English, and Chinese. 3.3 MAIN MENU 3.3.1 AE (AUTO EXPOSURE) Auto Exposure describes the brightness-related parameters, which can be adjusted by BRIGHTNESS, EXPOSURE MODE, AGC, and SENSE UP. BRIGHTNESS Brightness refers to the brightness of the image. You can set the brightness value from 1 to 10 to darken or brighten the image.
  • Page 10 ATW (Aoto Tracking White Balance) Under ATW mode, white balance is being adjusted automatically according to the color temperature of the scene illumination. MWB (Manual White Balance) You can set the R GAIN/B GAIN value from 1 to 255 to adjust the shades of red/blue color of the image.
  • Page 11 CONTRAST This feature enhances the difference in color and light between parts of an image. You can set the CONTRAST value from 1 to 10. SHARPNESS Sharpness determines the amount of detail an imaging system can reproduce. You can set the SHARPNESS value from 1 to 10.

  • Page 12: Save And Exit

    Select a MOTION area. Set the DISPLAY status as ON. Click the up/down/left/right button to define the position and size of the area. Set the SENSITIVITY from 0 to 100. CAMERA ID Edit the camera ID on this section. CAM ID SETTING Set the MODE as on.

Table of Contents