All manuals and user guides at all-guides.com ONTENTS OF THIS UIDE About the DISH Network EZ Remote Control....3 Buttons and Features Overview ........3 Installing Batteries.............. 4 Receiver Upgrade ............... 5 Setting Up to Switch the TV to Watch Satellite Programming ......... 5 Connecting Your Satellite Receiver and TV ....
Page 3
TV volume Cancel an action Enter channel and other numbers Recall the Mute the last channel TV sound RECALL MUTE Figure 1. The EZ Remote See How to Use the Remote Control for more details on each button. 118866...
Figure 1 on page 2 briefly describes each button on the DISH Network EZ Remote Control. Most of these buttons work the same way as the buttons on other DISH Network remote controls. See the User’s Guide for your DISH Network satellite receiver for a description of how your satellite receiver works with these buttons.
All manuals and user guides at all-guides.com To use these added buttons and other features to control your TV, follow the step-by-step instructions below to set up your remote control. This setup also requires you to connect your satellite receiver to your TV’s tuner using coaxial cable.
ATCH ATELLITE ROGRAMMING The following instructions show you how to set up your system and DISH Network EZ Remote Control so that when you press the TV gives you satellite programming every time. The first thing you will do is make the right connections between the TV and satellite receiver.
All manuals and user guides at all-guides.com ONNECTING ATELLITE ECEIVER AND 1. Connect a coaxial cable between the TV Set Out the satellite receiver and the tuner input on the TV (see Figure 2). : If you connect your TV a different way (for Note example, using yellow, red, and white audio/video RCA-type or S-Video cables), the feature to switch...
All manuals and user guides at all-guides.com ETTING P THE EMOTE TO ONTROL 1. Find the brand name of your TV in the TV code tables starting on page 32. You will be referring to this location for codes in the instructions below. 2.
All manuals and user guides at all-guides.com Press to change channels on • your TV. Press to change the TV volume. • If these buttons work, go on to the next section to set up . If not, pick another code for your TV brand from the TV Codes table and go back to step 3.
Page 10
All manuals and user guides at all-guides.com 7. Set the switch on the back of the satellite receiver to . The TV will lose the picture from the satellite receiver, but this is OK. : If your satellite receiver does not have a Note switch, see your satellite receiver’s User’s Guide for how to set...
Page 11
All manuals and user guides at all-guides.com Table 1: How I Change My TV Channels Column 1: Column 2: How do you change your TV to Circle the number Channel 3 using the number sequence you use to buttons? change your TV to Channel 3 “I just press the number buttons on my remote to change the...
Page 12
All manuals and user guides at all-guides.com 16.Write the number(s) you circled into the blank in step 19. 17.Press and hold until both lights turn on (it takes about five seconds). 18.Release light will flash. 19.Press (Fill in this blank with the exact sequence you circled in Table 1) 20.Press the button while watching light.
All manuals and user guides at all-guides.com ETTING WITCH THE TO A REFERRED HANNEL If you watch local programming from an off-air antenna, follow these instructions to set up to switch your TV to your preferred off-air channel. You will need to connect your off-air antenna to your satellite receiver and then set up your remote control.
All manuals and user guides at all-guides.com ETTING ON THE EMOTE ONTROL 1. In the blank below, write down your preferred off- air channel that you want your TV to tune to when you press 2. If step 19 on page 11 is blank and was not used to set up , go to step 8.
All manuals and user guides at all-guides.com 10.Release light flashes. 11.Press 12.Press the button while watching the MUTE light. 13.If the light flashes three times, go to step 14. If does not flash at all, go back to step 9. 14.Press to make sure your TV tunes to the off-air TV channel you wanted.
All manuals and user guides at all-guides.com , VCR, ONNECTING ATELLITE ECEIVER 1. Connect a coaxial cable between the TV Set Out the satellite receiver and the tuner input to the VCR (see Figure 4). : If you connect your VCR a different way (for Note example, using yellow, red, and white audio/video RCA-type or S-Video cables), the feature to switch...
All manuals and user guides at all-guides.com Step 3 Step 1 Step 4 Figure 4. Connecting a Satellite Receiver, VCR, and TV ETTING P THE EMOTE TO ONTROL 1. Find the brand name of your VCR in the VCR code tables starting on page 39.
All manuals and user guides at all-guides.com 8. If light flashes three times, the code is valid and you can go to step 9. If light does not flash at all, the code may not have been entered correctly. So, start over from step 3 and try the code again.
Page 19
All manuals and user guides at all-guides.com 6. Write the number in step 2 from page 15 into the blank in step 10 below. 7. Press and hold the until both lights turn on (it takes about five seconds). 8. Release light will flash.
Page 20
All manuals and user guides at all-guides.com Table 2: How I Change My VCR Channels Column 1: Column 2: How do you change your VCR Circle the number to Channel 3 using the number sequence you use to buttons? change your VCR to Channel 3 “I just press the number buttons on my remote to change the...
All manuals and user guides at all-guides.com 16.If the information in step 2 on page 15 is a “3,” write the numbers you circled in Table 2 into the blank in step 21. 17.If the information in step 2 on page 15 is a “4,” write the numbers you circled in Table 2 into the blank in step 21, except replace the “3”...
All manuals and user guides at all-guides.com THER EMOTE ONTROL NSTRUCTIONS TV C OW TO CAN FOR ODES If the code for your TV is not in the TV Codes tables starting on page 32, complete the following instructions to scan for your TV’s code.
All manuals and user guides at all-guides.com VCR C OW TO CAN FOR ODES If the code for your VCR is not in the VCR Codes tables starting on page 39, complete the following instructions to scan for your VCR’s code. 1.
All manuals and user guides at all-guides.com TV C OW TO HECK THE ODES You can find out what TV code is set up in your remote control when you complete the following instructions. 1. Hold until lights turn on (it takes about five seconds).
All manuals and user guides at all-guides.com TV C OW TO EMOVE ODES If you decide to change the TV you are using with the remote control, it is a good idea to remove the TV code from the remote. 1.
All manuals and user guides at all-guides.com OW TO SE THE EMOTE ONTROL This section describes how to use your DISH Network Remote Control. Figure 1 on page 2 shows the remote control with a brief description of the buttons. OINTING THE EMOTE...
Page 27
All manuals and user guides at all-guides.com TV POWER B UTTON Press the button to turn the TV ON or OFF. TV POWER This button works only if you have completed the instructions in Setting Up the Remote to Control Your TV on page 7.
Page 28
All manuals and user guides at all-guides.com UP/DOWN/LEFT/RIGHT B UTTONS Change channels - Press the button. • DOWN Open the - Press the button. • Browse Banner RIGHT Show - Press the button. • Themes LEFT Move around within the , the menus, •...
Page 29
All manuals and user guides at all-guides.com CANCEL CANCEL B UTTON Cancel - Press the button to cancel a • CANCEL procedure and go back to the previous menu or to watching a program. View - Press and hold the button until both •...
Page 30
All manuals and user guides at all-guides.com DISH B UTTON Press the button to go to Dish Home for receivers DISH that support Dish Home. RECALL RECALL B UTTON Recall - Press the button to return to the last • RECALL satellite receiver channel you watched.
All manuals and user guides at all-guides.com SING THE EMOTE ONTROL FOR ROGRAMMING HANNEL ONTROL UTTON To use the remote control to get programs from an off-air antenna and operate your TV, you must first press which will do three things: Turns off the satellite receiver to pass through your •...
Page 32
All manuals and user guides at all-guides.com CHANNEL UP/DOWN B UTTONS Use the buttons to change channels CHANNEL UP/DOWN on the TV. SELECT SELECT B UTTON button works as the button for a TV. SELECT ENTER UMBER UTTONS Use these buttons to enter numbers in a TV menu or directly enter a channel number.
All manuals and user guides at all-guides.com VCR C ODES These tables contain the manufacturer codes for programming the remote control to control your TV or VCR. Every attempt has been made to include all codes. If your TV or VCR is not listed or the codes do not work, the remote may not control your device.
Page 34
All manuals and user guides at all-guides.com TV Brand Code Circuit City Citizen 506, 516, 522, 523, 524, 525, 526, 691, Colortyme 573, 695 Concerto Contec 527, 528, 541, 591, 691 Craig 536, 541, 691, 694 Crown 526, 536 Curtis Mathes 506, 516, 526, 573, 703, 708, 712 541, 691 Daewoo...
Page 35
All manuals and user guides at all-guides.com TV Brand Code Fujitsu 534, 694 Funai 534, 541, 691, 694 Futuretech 541, 691, 694 General 503, 508, 509, 515, 540, 543, 544, 630, Electric (GE) 695, 698, 701,714, 715, 716 Genexxa Goldstar 505, 523, 526, 545, 546, 573, 588, 693, Granada 695, 711...
All manuals and user guides at all-guides.com IMITED ARRANTY This warranty extends only to the original user of the DISH Network remote control (“you,” “your”) and is limited to the purchase price of the remote control. EchoStar Communications Corporation and its affiliated companies (“we,”...
Page 47
All manuals and user guides at all-guides.com PERFORMED PROPERLY. THIS WARRANTY SHALL BE VOID IF ANY FACTORY-APPLIED IDENTIFICATION MARK, INCLUDING BUT NOT LIMITED TO SERIAL OR CONDITIONAL ACCESS NUMBERS, HAS BEEN ALTERED OR REMOVED. THIS WARRANTY SHALL ALSO BE VOID IF THE DEVICE HAS BEEN OPENED BY AN UNAUTHORIZED PERSON (with the exception of opening the battery cover).
Page 48
CCESSORY ARRANTY An accessory is any DISH Network branded equipment, displaying the DISH Network logo, excluding the receiver, Smart Card, cables and hookups, and non-mechanical components. A one-year warranty becomes effective upon the activation of the DISH system or date of purchase, if bought separately.
Page 49
All manuals and user guides at all-guides.com 6. Write the RA number in large, clearly visible characters on the outside of the shipping box used to return the equipment. To avoid confusion and misunderstandings, we will return shipments without an RA number clearly visible on the outside of the box to you at your expense.
Page 50
EMOTE ONTROL OMPATIBILITY This remote control is supported by all DISH Network receiver models except 7100/7200 (DISHPlayer), Model HM-DSR100RU (JVC-DVHS), some 2000, 4000, and 5000. Also, the channel control features on the remote control do not work with the Model 6000.
Page 51
Please send any comments or questions directly to: EchoStar Technologies Corporation, Technical Publications, 94 Inverness Terrace East, Englewood, Colorado 80112 Part Number: 118866 Printed in the United States of America. DISH Network is a registered trademark of EchoStar Technologies Corporation.
Page 52
All manuals and user guides at all-guides.com For ALL your customer needs, call the Customer Service Center at 1-800-333-DISH (3474). 118866...