Sawo HEATERKING DRFT6-80Ni-WL Manual page 17

Tehoyksikkö
Power Controller
Control Unit Main Switch
1 1 0 1
F1
Fuse Glass
Primary
Supply
160 mA
Max. 15.0 kW
400V 1N~
Fuse Glass
Light
500 mA
W
R-in S-in T-in N N U U V W
N
B
V
PE
R (L1)
S
(L2)
(L3)
T Ground
N
PE
Power Supply
The cable must be
HO7RN-F type or its
equivalent. 5 core cable
Model kW H1
DRFT12-180Ni-P-WL 18.0 1.5
DRFT12-210Ni-P-WL 21.0 1.5
DRFT12-240Ni-P-WL 24.0 2.0
18
SUOMI | ENGLISH
3 Vaihe
3 Phase
Built-in Control For Built-in Controls, Jumper For
Models remove the interface Maximum Session Time
PCB to access the
(hours)
Session Time jumper.
6h 18h
Make sure that pin header
terminal is properly inserted
to UIB socket terminal.
1
4h 12h 24h
Fuse Glass
JPB1
Fan & Combi
500 mA
F3
F2
RJ12 - Data Cable
1 meter
2 1 1 D 1 3
4 meters
U N N
N 3 4 4 D 2 4
T/H Sensor
T/H Sensor
T/H Sensor
T/H Sensor
TS2
TS2
TS1
TS1
2 4
3 1
FUS TS
Light
TS1
Temperature
Sensor
110 W
with Fuse
AC1
H2 H3 H4 H5 H6 H7 H8 H9 H10 H11
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1.5 1.5 1.5 1.5 1.5 2.0 2.0 2.0 2.0 2.0
2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
Adjust this jumper
to change max.
JPB1
session time. 6hrs
is factory default.
Only for Separate Control Interface
Classic Touch SS Touch
Note:
If no door sensor is installed, "Door
switch" terminals in the Power Controller
must be connected with each other by a
jumper wire from terminal D to terminal D.
Note:
Do not connect both
4 2 4
1 3 1
Optional Sensors same
time. Only one of the
FUS TS FUS TS
optional sensors at a
time is allowed.
Sensors
T/H Sensor
TS2
Optional
Optional
Temperature Sensor Temperature &
for Bench Area Humidity Sensor
Terminal 1 Terminal 2
U V W N U V W N
H12
HEATER
1.5
2.0
2.0
Kontaktoriyksikkö
Contactor
Control Unit Main Switch
1 1 0 1
F1
Fuse Glass
Primary
Supply
160 mA
Max. 15.0 kW
400V 1N~
Fuse Glass
Light
500 mA
R-in S-in T-in N N N U U
B
Classic 2.0
R (L1)
S
(L2)
PE
T (L3)
N
PE
Ground
Power Supply
The cable must be
HO7RN-F type or its
equivalent. 5 core cable
Built-in Control For Built-in Controls,
Models remove the interface
PCB to access the
Session Time jumper.
Make sure that pin header
terminal is properly inserted
to UIB socket terminal.
Fuse Glass
JPB1
Fan & Combi
F3 500 mA
F2
2 1 1 D 1 3
V W
19
SUOMI | ENGLISH