Sony HDCU1700 Operation Manual page 27

SYSTEM OPERATION
Page name Item
Page No.
<MULTI FORMAT> FREQUENCY
S03
Notes
CAMERA FORMAT
• FREQUENCY or
CAMERA FORMAT
mode setting changes
take effect only after the
CCU power supply is
turned off and then on
again.
• Notes when changing
FRAME CONVERT
FORMAT
DELAY
When BPU is attached,
confirm if the FORMAT
CCU VIDEO
of BPU is set correctly
CONVERT
after changing the
FORMAT of CCU.
Also, when you change
the FORMAT of BPU,
change the FORMAT of
CCU beforehand.
3G-SDI
HD-SD DELAY
COMPONENT
<OUTPUT FORMAT> CAMERA TRANSMIT
S04
SLOT2 (board name)
SLOT3 (board name)
Settings
HD 1.001, 1.000
SD (525NTSC), (625PAL)
When FREQUENCY is set to
1.001: 1080/59.94I, 1080/
29.97PsF, 1080/23.98PsF, 720/
59.94P, 1080/59.94P(4K/HDR)
When FREQUENCY is set to
1.000: 1080/50I, 1080/25PsF,
1080/24PsF, 720/50P, 1080/
50P(4K/HDR)
0.8, 1.2, 1.6
DSB, ENB
Level A, Level B
Line, Frame (1F), 0-Delay
RGB, YCD
When FREQUENCY HD is set to
1.001: 1080/59.94I, 1080/
29.97PsF, 1080/23.98PsF, 720/
59.94P, 1080/59.94P(4K/HDR)
When FREQUENCY HD is set to
1.000: 1080/50I, 1080/25PsF,
1080/24PsF, 720/50P, 1080/
50P(4K/HDR)
1&2 Output format*
3&4 Output format*
OETF S-Log3, HLG_BT.2100, HLG_Live,
SDR
COLOR BT.2020, BT.709
1&2 Output format*
3&4 Output format*
OETF S-Log3, HLG_BT.2100, HLG_Live,
SDR
COLOR BT.2020, BT.709
Description
Selects the operating frequency.
Selects the transmission format.
Note
Selectable items differ depending on the camera's
supported format.
Sets the output delay for framerate-converted signals.
(Displayed only when FREQUENCY HD is set to 1.001.)
Sets video conversion. When CAMERA FORMAT is
set to 1080/59.94P or 1080/50P, set to ENB to
convert/output 720/59.94P or 720/50P signal from
the DRX board. To set to ENB, set FRAME
SYNCHRO in RETURN SETUP (S07) to ON.
(Displayed only when HKCU2007 or HKCU2040 is
installed.)
Tip: When CCU VIDEO CONVERT is set to ENB, the
CCU internal video conversion is delayed, so adjust
the camera's signal by advancing it as necessary.
Selects SMPTE425 Level A or SMPTE425 Level B
for 3G-SDI output.
Sets the phase output for SD signals down
converted from this unit's HD signals.
Selects the component signal connector's output
format.
(Displayed only when HKCU1003 is installed.)
Selects the output format.
This setting works in conjunction with CAMERA
FORMAT.
Note
Selectable items differ depending on the camera's
supported format.
Selects the output format for expansion slot 2's SDI
OUT1/2 connector.
Selects the output format for expansion slot 2's SDI
OUT3/4 connector.
Selects OETF for expansion slot 2.
(Displayed only when HKCU2040 is installed.)
Selects COLOR SPACE for expansion slot 2.
(Displayed only when HKCU2040 is installed.)
Selects the output format for expansion slot 3's SDI
OUT1/2 connector.
Selects the output format for expansion slot 3's SDI
OUT3/4 connector.
Selects OETF for expansion slot 3.
(Displayed only when HKCU2040 is installed.)
Selects COLOR SPACE for expansion slot 3.
(Displayed only when HKCU2040 is installed.)
27