Summary of Contents for Zerotech YS-S4
- Page 1 YS-S4 Multi-rotor Autopilot User Manual V1.4 YS‐S4 Multi‐rotor Autopilot User Manual V1.4 Zero UAV (Beijing) Intelligence Technology Co. Ltd 1 ...
-
Page 2: Table Of Contents
YS-S4 Multi-rotor Autopilot User Manual V1.4 Table of Contents Table of Contents ............................... 2 1. Warning and Disclaimer ............................ 3 2. In‐the‐Box ................................ 4 3. Functions ................................ 5 4. Installation ................................ 6 5. Connections ................................ 7 5.1 Assembly ................................ 7 5.2 How to connect the modules .......................... 8 6. Configurations Before Flying .......................... 9 6.1 Install Phone GCS .............................. 9 6.2 Tx Setup ................................ 10 6.3 Parameter Setup .............................. 12 6.3.1 PC Parameter Adjustment .......................... 12 6.3.2 Phone Parameter Adjustment ......................... 14 6.4 Tx Calibration .............................. 14 6.4.1 Transmitter channel calibration by PC...................... 14 6.4.2 Tx Calibration by Phone .......................... 16 6.5 Fail/Safe Checking .............................. 17 7. Adjustment Outdoors ............................ 18 ... -
Page 3: Warning And Disclaimer
YS-S4 Multi-rotor Autopilot User Manual V1.4 Warning and Disclaimer Thank you for purchasing this ZERO UAV product. The product is an advanced and specifically dedicated control item. Any misuse may result in damage to property, injury or even death. The user must conform to the law and use the equipment responsibly. This product is not suitable for people under the age of 18. Please read this disclaimer carefully before using the product, or visit the YS‐S4 web page at http://www.zerouav.com to refer to relevant updates or information. Warning Please keep the product out of reach of children. Make sure the aircraft is kept away from people and dangers such as buildings roads and property. We suggest you fly your aircraft at specially designated areas. Please do NOT fly this product when affected by drunkenness, tiredness, drugs, dizziness fatigue, nausea or any other condition that might impair your ability to control the aircraft. Please strictly follow the user manual when operating the device. Please make sure all components of the device are connected and work well, otherwise your unit may be damaged, destroyed or even buried! ... -
Page 4: In-The-Box
YS-S4 Multi-rotor Autopilot User Manual V1.4 components have obvious faults, obvious defects or missing accessories). 11) Damage(s) or injuries caused by flying in the following situations: Using the aircraft in a magnetic interference area, radio interference area or government regulated no‐fly zones, in bad light, when the pilot has blocked, fuzzy or poor eyesight or in any other conditions not suitable for operating. 12) Damage(s) or injuries caused by using in bad weather, including rain, wind (more than a moderate breeze), snow, hail, lightning, tornado, hurricane etc. 13) Damage(s) or injuries caused when the aircraft is in the following situations: collision, fire, explosion, flood, tsunami, subsidence, ice trapped, avalanche, debris flow, landslide, earthquake, etc. 14) Damage(s) or injuries caused by infringement such as litigation caused by any data, audio or video material recorded by the use of aircraft. 15) Damage(s) or injuries caused by the misuse of the battery, protection circuit, RC model and battery chargers. 16) Other losses that are not covered by the scope of ZERO TECH liability. In the Box ■ Hardware □ Software ... -
Page 5: Functions
YS-S4 Multi-rotor Autopilot User Manual V1.4 ■ Power Module x1 Supplies regulated power for the autopilot ■GPS Bracket x1 The GPS＋COMPASS is sensitive to magnetic interference. This bracket is used to mount the GPS module where necessary and to keep it far away from EMI sources. ■Warranty Information Card X1 This provides Product Serial No., Purchase Date. Please fill out the relevant information and return to Zero UAV to register your product warranty. Software available on website for download: □ GCS So ware for Android System □ GS Software for PC Windows XP/7/SP3 system □ Firmware Upgrade So ware on PC. □ Firmware updating assistant. Functions Supported multirotor layouts: Quad X4, Quad +4, Hexa X6, Hexa +6. Four working modes: Manual flight stabilisation ... -
Page 6: Installation
YS-S4 Multi-rotor Autopilot User Manual V1.4 Installation 4.1 YS‐S4 Module Installation The YS‐S4 Module should be placed level on the main body of the aircraft. For best results install at the Center of Gravity (CoG) of the aircraft. The “ Front Arrow” MUST point towards the head of the aircraft: Towards aircraft nose IMPORTANT: The YS‐S4 will adapt to most aircraft types without inner dampening. It may not adapt satisfactorily to larger aircraft in which case the YS‐S4 should be mounted on the optional dampening structure shown below and available from ZeroUAV. YS‐S4 dampening structure ... -
Page 7: Connections
YS-S4 Multi-rotor Autopilot User Manual V1.4 Connections Assembly IMPORTANT Ensure the original factory supplied power module is used. The manufacturer holds no responsibility if the S4 is burnt out by using any other power module. The Power supply module and the WI‐FI module must connect to a 3S‐6S LIPO battery. The voltage range would therefore be 10.8V‐25.5V. Normally this would be your main flight battery. The RC receiver (PPM supported) is powered directly from the MC. DO NOT power the receiver with any additional module or the YS‐S4 unit may be burnt out. Motors and ESCs (Especially when several ESCs are together), can cause serious magnetic interference so the GPS module must be as far away from these as possible. A non‐ferric bracket must be used with the arrow on the GPS facing forward. Also the battery connection carries a high current and may result in a strong magnetic field. Keep the battery wires as far away as possible from the GPS module otherwise your aircraft may fly in circles! If using a servo gimbal, make sure the SERVOs are powered separately. WHITE core wire is always the signal line, the RED core wire is positive; the BLACK core wire is ground (0v). 7 ... -
Page 8: How To Connect The Modules
YS-S4 Multi-rotor Autopilot User Manual V1.4 Only the USB interface can be used for Parameter Setting and Firmware Upgrade. The COM port is also an interface to connect to a WI‐FI module. The YS‐S4 DOES NOT support ESC calibration The ESCs should be calibrated independently referring to the manufacturer supplied ESC manual. It is a good idea to disable the ESC low‐voltage cut out. With most ESCs all you need do is configure them to NiMH. How to Connect the Modules 1) Connect the power supply module As shown below, one 3‐core cable is used to connect the S4 to the power unit, the WHITE‐core is up, the RED‐core is in the middle and the BLACK‐core is below. The RED and BLACK bare wires should to be soldered to the Positive and Negative pole of the battery pack connector (3S‐6S Lipo). 2) Connect the LED module The LED module should be connected to the LED interface of the S4 main controller as shown. 3) Connect the GPS module The GPS module has red and black ends; the RED end is connected to the S4 GPS‐R interface, and the black end to the GPS‐B interface. The side of the slot faces up. 4) Connect the receiver 8 ... -
Page 9: Configurations Before Flying
YS-S4 Multi-rotor Autopilot User Manual V1.4 The receiver should be connected as follows: the WHITE wire (signal) is up, the RED wire (positive) is in the middle, and the BLACK wire (ground) is at the bottom. The ESC wires should be connected in the same way but NB: If your ESCs have a BEC (supply voltage via a battery equivalence circuit) then you must remove the red wire from each. If you are not sure about the BEC, remove the red wire anyway! 5) Connect the WI‐FI Module (extended connection) The WI‐FI data cable is a 3‐core cable, connect the end which has the lock to the WI‐FI module and connect the other end to the COM interface on the YS‐S4 (white wire is up, red is in the middle, black is below). The WI‐FI module should be powered separately; power supply range is 3s‐6s Lipo. Configuration before Flying Install Phone Ground Control Software (GCS) ... -
Page 10: Tx Setup
YS-S4 Multi-rotor Autopilot User Manual V1.4 S4V2‐GCS Start the GCS; you will see the serial number and firmware version for the autopilot on the interface once the data has connected. After connecting your WI‐FI to the GCS successfully, you can also see the real‐time updated data on the "Data" Page. 6.2 TX Setup Select fixed wing model on your transmitter. Remove any channel mixing. FUTABA Radio: All channels should be Normal (not reversed). JR, JTm, Spektrum and WFLY Radios: Reverse all channels. Step 1: Select Two Switches Ensure your radio has two sets of two‐way switches. Programme CH5 and CH6 to these switches to control the flight modes: 10 ... - Page 11 YS-S4 Multi-rotor Autopilot User Manual V1.4 CH5 Position1—Manual Stabilization Mode CH6 Position1—Neutral CH5 Position2—Auto Mode CH6 Position2 — Return and Land Adjust your two‐way switch end points to control the flight modes: CH5 Position CH6 Position GPS Status Working Mode Position 1 Position 1 X Manual Stabilization Position 2 Position 1 GPS No Lock Manual Altitude Hold GPS Lock（above 5 satellites） Auto Hover X Position 2 Return and Land GPS Lock（above 5 satellites） IMPORTANT: ...
-
Page 12: Parameter Setup
YS-S4 Multi-rotor Autopilot User Manual V1.4 THR is set to 50% (mid‐point) Check with your Radio manual on how to set the Receiver failsafe. Here you can choose any of the following F/S modes: Auto RTH and Land; Auto Land and Auto Hover. Now the YS‐S4 autopilot will control the aircraft according the pre‐programmed F/S mode if the aircraft loses the TX signal. (set this up on the PC software under “Fail Safe” options) Please refer to this video for help setting up your TX: http://www.tudou.com/programs/view/e1ai526Mbt4/ 6.3 Parameter Setup YS‐S4 Parameter setting can be achieved using a mobile phone or tablet (must be connected to WI‐FI) or by using a PC to adjust the parameters. 6.3.1 PC Parameter Adjustment Please download the special “PC‐Parameter Setup Software” from the Zero website before parameter ... - Page 13 YS-S4 Multi-rotor Autopilot User Manual V1.4 Roll sensitivity and Pitch sensitivity would affect the degree of command response in flight (Default value is 45, range 0‐255), Motion Compensation can increase stability but would decrease the sensitivity (Default value is 20, range0‐255). Roll/Pitch sensitivity is used to adjust the compensation angle of the PTZ data for your Gimbal. Your can compensate high or low for aircraft movement within a range from -127 to 127 (Note: You can enter a negative ...
-
Page 14: Phone Parameter Adjustment
YS-S4 Multi-rotor Autopilot User Manual V1.4 The maximum height and distance allowed can be specified. The maximum is 1500 meters, min 10 meters. Set up Fail/Safe mode（Auto RTH and Land, Auto Land and Auto Hover are the ... - Page 15 YS-S4 Multi-rotor Autopilot User Manual V1.4 In the PC GCS select the "Stick Layout" drop‐down menu. The “Hand Mode” is your transmitter mode (Mode 1, Mode 2, Mode 3 etc.) Select the mode according to your preference and the stick layout of your TX. Step2: Calibrate the sticks The ‘Adjust Transmitter’ window will appear on the PC GCS. Click ‘OK’ and move your transmitter stick within 5 Seconds to their maximum positions as shown in the diagram: Step 3: Check that the stick direction as depicted on the screen matches the actual direction of movement of your sticks. 15 ...
-
Page 16: Tx Calibration By Phone
YS-S4 Multi-rotor Autopilot User Manual V1.4 Check that the display of each stick shows that TX is calibrated well. This screen displays the position of the sticks. On the left is the Rudder and Elevator (Mode 1 depicted). On the right is the aileron and THR stick (Mode 1 depicted). When both sticks are in the middle position they are shown as GREEN, any other position shows RED except for when the throttle stick is at the bottom when it shows as YELLOW. When the throttle is in hover position (normally close to the middle position) it shows GREEN, other flying status shows RED. TX Calibration by Phone 6.4.2 Step 1 Select the correct stick layout (Mode 1, Mode 2, Mode 3 etc.) Click the menu button on your phone then select "Set” (see below) In the "Set" box which opens select the "Hand Mode" drop‐down menu. The “Hand Mode” is your transmitter mode (Mode 1, Mode 2, Mode 3 etc.) 16 ... -
Page 17: Fail/Safe Checking
YS-S4 Multi-rotor Autopilot User Manual V1.4 Select your own operation style in the hand mode menu. The illustration shows “Japan Hand” which is Mode 1. Step 2 Calibrate the sticks Click the button “Adjust Transmitter” on GCS “Data” and click "OK" in the dialog box. Move both sticks to their end points in a circular motion within 5 Seconds. The autopilot will store the maximum and minimum end points and also the mid points of both sticks. 6.5 Fail/Safe Checking Step 1 Check that Flight Modes change on TX command: Check Flight Modes via the Configuration software ‘Flight Mode’: Assuming your GPS module is connected; check whether switching between all working modes is working normally. For example: Place CH5 at position1 and CH6 at position1, the PC GCS "data" page should show your TX status as "Manual", Change CH5 to position 2 for Auto Hover and so on. If flight mode does not change when you toggle the switches please check your hardware connections or RC Transmitter setup. Step 2: Fail Safe (F/S) Checking ... -
Page 18: Adjustment Outdoors
YS-S4 Multi-rotor Autopilot User Manual V1.4 SWITCH OFF the RC Transmitter whilst the autopilot is still powered on, the ‘Flight Mode’ should switch to display "Return and Land", “Land” or “Auto hover” ( these options are the chosen F/S settings from your PC GCS ) the throttle stick indicator should be in the middle and displayed in GREEN. If not, please setup the fail‐safe (F/S) again. ... -
Page 19: Compass Alignment By Without Smartphone
YS-S4 Multi-rotor Autopilot User Manual V1.4 7.1.1 Compass alignment without Smartphone. Step 1 Move CH5 and CH6 on the transmitter to Position1 and make sure Channel 5 & 6 switches are in position 1 ( Manual Mode). Level your multicopter. Flip CH5 switch three times quickly between Position 1 and Position 2( 1 > 2 > 1 > 2 > 1 > 2 > 1) and the LED turns green. You have entered Horizontal Calibration. Step 2 Rotate the multicopter counter clockwise( or clockwise) three times. ENSURE that the GREEN LED remains ON during this procedure. If it turns OFF, it means the aircraft is not horizontal. Adjust the position until the GREEN LED is back ON and continue with the rotation and put the multicopter level again. Step 3 Flip CH5 switch three times(1 > 2 > 1 > 2 > 1 > 2 > 1) and the LED turns off. You have entered Vertical Calibration. Hold the multicopter nose down and the LED turns green. Rotate the multicopter 3 times counter clockwise as shown below, always keeping the aircraft nose down. Ensure the GREEN LED remains ON during the turn. If the LED turns OFF, adjust the attitude of the multicopter until the GREEN LED is back ON and continue with the rotation and put the multicopter level again when finished the rotation. The LED turns off. Step 4 Flip CH5 switch three times (1 > 2 > 1 > 2 >1 >2 >1)quickly and the LED turns green. Wait until the LED turns off. That indicates the compass calibration is done. 7.1.2 Compass alignment using Smartphone Step 1 Click the “Magnetic Compass” button on the Phone GCS "Data" Page: ... - Page 20 YS-S4 Multi-rotor Autopilot User Manual V1.4 Step 2 Select "Horizontal Alignment" in the dialog box, and then click "OK" button to start level calibration. If you don't want to keep calibrating select "Cancel" and confirm “OK”. Step 3 Level your aircraft and carefully turn around horizontally three times. ENSURE that the GREEN LED light remains ON during this procedure. If it turns OFF, that means the aircraft is not horizontal. Adjust the position until the GREEN LED is back ON and continue with the rotation. Step 4 Select "Vertical Alignment" in the dialog box, and click "OK" button to start the vertical calibration. If you don't want to keep on calibrating select "Cancel" and confirm “OK”. Step 5 Carefully rotate the aircraft 3 times as shown below, always keeping the aircraft nose down. Ensure the GREEN LED remains ON throughout the turn. If the LED turns OFF, adjust position until the GREEN LED is back ON and continue with the rotation 20 ...
-
Page 21: Motor Arming
YS-S4 Multi-rotor Autopilot User Manual V1.4 Step 6 Click "Save Alignment" the dialog box, and click "OK". Step 7 Now the GCS software will automatically switch to the “Control” interface screen and after a period of calculation will display two circles, a BLUE one and a RED one. The YS‐S4 will enter the magnetic recording and the LED will now flash GREEN. Calibration will be completed seconds later when the GREEN flash turns OFF. Excellent ... -
Page 22: Motor Mixer Checking
YS-S4 Multi-rotor Autopilot User Manual V1.4 After the CSC operation, push the THR stick slightly up. The motors should begin to turn. You need to apply more throttle to take off normally. 7.3 Motor Mixer Checking Before take‐off, you still need to check your motor mix control. First let’s take the quadcopter + type as an example to simply describe how to check motor mix control (Please refer to the illustration for other aircraft configurations). You need to arm the motors and check what happens when you advance the throttle stick, if the four motors rotate at the same speed this means the motor balance is good. 1. To check the aileron channel, slightly push the aileron stick to the left, motor M4 should rotate immediately (see 1 on the illustration below), the other three motors should keep still. Push the aileron stick to the right slightly, motor M2 should rotate immediately (see 2 on the illustration below), the other three motors should keep still. 2. Check the elevator channel. According to the aircraft symmetry it should be similar to checking the aileron channel. Push the elevator stick up slightly, motor M3 should start to rotate (see 3 on the illustration below) now slightly pull the elevator stick down and motor M1 should start to rotate immediately (see 4 on the illustration below). Quadcopter X type 22 ... -
Page 23: Tasks
YS-S4 Multi-rotor Autopilot User Manual V1.4 Hexacopter+ type： Hexacopter X type： 8. Tasks 8.1 Servo Gimbal Powering the servos when using a gimbal with the S4: Servo Battery Gimbal Servo Signal Y1/Y2 Connector Connect Y1 to the gimbal roll servo and Y2 to the gimbal pitch servo. Enter “Roll Sensitivity” and “Pitch Sensitivity” in the Parameter Section of the GCS to adjust the correction angle and direction of your gimbal. Gimbal Sensitivity ranges from ‐127 to 127. A negative number reverses the direction of travel and the size of the number affects the amount of correction. 23 ... -
Page 24: Firmware Upgrade
YS-S4 Multi-rotor Autopilot User Manual V1.4 You will need a TX with at least 7 channels to use the Gimbal function. Use channel 7 on your transmitter for gimbal control and assign it to a knob switch, Channel 7 will now adjust your gimbal pitch location and will continue to stabilize the camera at all angles of pitch. The spare channels may be used for other applications. Normally roll servos will maintain gimbal stabilization in the middle position. If your gimbal tilts to one side it can be adjusted it by clicking “Enter Setup” in the Setting section (CH5 must in manual and the throttle set to minimum) Now the CH7 knob can be used for controlling gimbal roll. The gimbal roll’s balance position may be fixed and saved by clicking “Quit Setup”. Now CH7 will revert to controlling gimbal pitch. Firmware Upgrade IMPORTANT: For safety, please remove all the propellers before upgrading firmware. You may download the latest firmware and assistant tool from the ZeroUAV website before upgrading the firmware. (1) Connect the YS‐S4 to the computer with a Mini USB cable. Power the S4 and put bring the throttle stick to the bottom. (2) Open the S4 Setup Software “ S4‐GCS‐USB.exe”, Click “Open USB” button in the “YS‐S4 firmware upgrade” window. 24 ... - Page 25 YS-S4 Multi-rotor Autopilot User Manual V1.4 3) Click “OK” 4) Click “Select Firmware” button 25 ...
- Page 26 YS-S4 Multi-rotor Autopilot User Manual V1.4 5) Click “Open” button, select upgrade procedure file“s4v2‐BiaoZhun‐20140115‐v021.bin” 6) The program will auto‐upgrade when the upgrade procedure is selected. 7) Power‐off the autopilot when it says “upgrade successful”. Quit the firmware upgrade software and power off the autopilot. 26 ...
-
Page 27: Appendix
YS-S4 Multi-rotor Autopilot User Manual V1.4 Appendix LED Indicator Interpretation: The working status of the S4 is basically indicated by the GREEN + RED LEDs, see below: Flight Status LED status Description Manual（GPS NOT LOCKED） 1 second GREEN and 1 second RED Manual（GPS LOCKED） 2 seconds Green once per loop Manual altitude‐hold 2 seconds GREEN and 1 second RED Auto‐hover 3 seconds GREEN First stage low voltage alert 2 seconds RED Final stage urgent low voltage alert 3 seconds RED Return and Land Continuous RED flashing ... -
Page 28: Flight Mode Description
YS-S4 Multi-rotor Autopilot User Manual V1.4 Flight Mode Description IMPORTANT Make sure the TX is on first and the throttle stick is at the bottom. DO NOT push the THR stick to the bottom during flying. DO NOT switch to auto‐fly mode until the craft is stable in manual stabilization mode. Switch to manual stabilization mode if craft meets an emergency situation in auto‐fly mode. (1) Phone/ Tablet Control (1) Phone Remote Control Mode During flight, when the transmitter is switched to “Auto‐hover” in “GPS mode”, the aircraft will enter auto‐hover mode. Now you can activate control of your aircraft via your cellphone by pressing “Enable Control” in the “Control” screen of your GCS. NB: When in phone remote control mode, your transmitter control will not work. 28 ... - Page 29 YS-S4 Multi-rotor Autopilot User Manual V1.4 How to control your multi‐rotor by phone or tablet? Enable Control User Interface Operations Aircraft Status Red: GPS not locked Circle status ‐ Green: GPS locked. Position Hold No Operation Position hold Drag finger over screen: 1．move forward/backward 1. up/down 2．move left/right Level Flight 2. left/right 3．Move left/right top, 3. left/right top, left/right bottom etc. left/right bottom etc. Click below the area inside the cross 1.over circle 2.under circle 3. Left of circle 4. right of circle 1、Climb NB: Climb – Descend ...
- Page 30 YS-S4 Multi-rotor Autopilot User Manual V1.4 In this mode, craft will hold the altitude but not hold the position. When the THR stick is in its 50% position the craft will hover in the current altitude but not at its current position (the craft will drift when the GPS is not locked), but the craft can still be controlled manually. Left/right is controlled by the AILERON Stick, Up/Down controlled by the ELEVATOR stick, direction is controlled by the RUDDER stick, and height controlled by THR stick. If the THR stick is 50%, craft will auto‐hover; If THR stick is more than 50%, craft will fly upward; If THR stick is less than 50%, craft will descend. The Craft can fly to any altitude controlled by THR stick, and fly to any position controlled by the other sticks. (4) Auto hover With GPS located (when satellites locked are more than 5) and CH5 is in position2 and CH6 in position1, the S4 will enter auto‐hover mode. In this mode, the aircraft will hold its position and altitude. Your TX sticks should all be in the mid position. When THR stick is around the mid position the craft will hover in its current position, (The craft does not drift because GPS has locked) and also may controlled manually. Left/right is controlled by the AILERON Stick, Up/Down controlled by the ELEVATOR stick, direction is controlled by the RUDDER stick, and height controlled by THR stick. If the THR stick is 50%, craft will auto‐hover; If THR stick is more than 50%, craft will fly upward; If THR stick is less than 50%, craft will descend. The Craft can fly to any altitude controlled by THR stick, and fly to any position controlled by the other sticks. (5) Return and Land (RTL) With GPS locked (more than 5 satellites locked) and Motor arming done, the craft will record its home position. ...
- Page 31 YS-S4 Multi-rotor Autopilot User Manual V1.4 V2 will maintain its previous altitude during RTH. Safety: Since RTH is fully autonomous and you cannot alter the flight path during RTH, to avoid accidents, it is not advisable to activate RTH too close to you or spectators. Also note to avoid sudden loss in altitude, the THR stick should be above its mid‐point when you change the mode back from RTH to Stabilized Mode. Switch CH6 to position1 from position2 to quit RTL mode. After landing the motors will stop. Move your THR stick to the bottom, 5 seconds later the motors will lock. Arm the motors to restart flying. Support Website：www.zerouav.com Telephone：0086‐10‐57250711 31 ...