Advertisement
Please read carefully: Read through these instructions completely before commencing installation. Retain for future use.
This product should be installed by a licensed electrical contractor or similarly qualified person.
1
Specifications
Cat. No.
Supply voltage
Power rating
Appliance class
Standby power
IP rating
Draught stopper
Duct size
Engine size
Engine weight
Power cord length
Ceiling cut-out size (for inlet &
outlet grilles)
Warranty
Max airflow (m
3
/hr)
Duct length
No duct
1m per side (total 2m)
2.5m per side (total 5m)
Sound Pressure Level: dBA at 3m (Tested in accordance with AS1217.5)
EFIL100SQWE
High Speed (I)
38
2
Features
The inline fan is designed to extract steam and odours from a bathroom and expel it to the exterior through an eave outlet. It is also suitable for
extracting air from one room and expelling it to another room (heat distribution).
The fan engine is fitted into the ceiling, well away from the inlet. This inline feature allows the inlet grille to be mounted in wet areas (near the splash
zones of bathrooms) or even above the shower. And because the motor is in the ceiling cavity (away from the inlet grille), noise from the fan is minimal.
Inline Exhaust Fan Kit–100mm &150mm
EFIL100SQWE
30W
N/A
5m X Ø100mm
290 x 200 x 210mm
1.9kg
1m
Ø110mm
5 year
EFIL100SQWE
Low Speed (I)
200
100
90
Low Speed (II)
34
Cat. No. EFIL100SQWE, EFIL150SQWE,
EFIL150SQWE
230-240V AC 50Hz
60W
Class II
IP55
Yes (PET Sheet)
5m X Ø150mm
290 x 230 x 250mm
3.0kg
Ø160mm
EFIL150SQWE / EFTIL150SQWEKIT
High Speed (II)
Low Speed (I)
255
450
125
310
115
270
EFIL150SQWE/ EFTIL150SQWEKIT
High Speed (I)
47
EFTIL150SQWEKIT
Instruction Manual
EFTIL150SQWEKIT
<1W
N/A
3 year
High Speed (II)
555
390
335
Low Speed (II)
42
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for LEGRAND HPM EFTIL150SQWEKIT
Summary of Contents for LEGRAND HPM EFTIL150SQWEKIT
- Page 1 Inline Exhaust Fan Kit–100mm &150mm Cat. No. EFIL100SQWE, EFIL150SQWE, EFTIL150SQWEKIT Instruction Manual Please read carefully: Read through these instructions completely before commencing installation. Retain for future use. This product should be installed by a licensed electrical contractor or similarly qualified person. Specifications Cat.
-
Page 2: Things To Consider
Things to consider 1. This product shall be installed in accordance to AS/NZS 3000 Wiring Rules. 2. This product is meant for indoor use only. 3. Regulations concerning the discharge of air must be fulfilled. Local building codes may require venting to the outside. 4. -
Page 3: Air Inlet
Inlet and Outlet Grilles Fig 5: 2 types of grilles are supplied with this product. Fig. 5 Outdoor Grille Indoor Grille For 100 Ducts For 100 Ducts Footprint on ceiling: 129 X 129mm Footprint on Wall/ceiling: 125 X 125mm Protrusion from ceiling: 23mm Protrusion from Wall/ceiling: 17mm For 150 Ducts For 150 Ducts... -
Page 4: Installation
Orientation of the junction box can be adjusted to suit the fan engine’s Fig. 8 Engine mounting location. Clamps 1. Unscrew and open the engine clamps. 2. Rotate the Engine to the desired position of the junction box. 3. Replace the engine clamps and tighten the screws. Installation Before commencing installation, remove all packaging from the product and ensure that power to the circuit has been isolated. -
Page 5: Timer Function
8. This product contains no serviceable parts and no attempt should be made to repair it. If the product is faulty it should be discarded. 9. If the supply cord is damaged, it must be replaced by Legrand, its service agent or a similarly qualified person in order to avoid a hazard.
Need help?
Do you have a question about the HPM EFTIL150SQWEKIT and is the answer not in the manual?
Questions and answers