Advertisement
Quick Links
Advertisement
Related Manuals for V-fit MCCT-2
Summary of Contents for V-fit MCCT-2
- Page 1 SERIAL NO: FC2995-UK MCCT-2 Magnetic 2-in-1 Cycle-Cross Trainer...
-
Page 3: Table Of Contents
Contents Section Page General Information ..4 Before You Start ..5 Safety ....6 Exercise Information . -
Page 4: General Information
General Information Quality Guarantee This exercise product has been designed and This product is guaranteed for DOMESTIC USE ONLY for manufactured to comply with the latest (BS EN 957) a period of 1 YEAR from the original certified date of British and European Safety Standards. -
Page 5: Before You Start
Before you Start Tools If required, most of our products are supplied with basic tools, which will enable you to successfully assemble your product. However, you may find it beneficial to have a soft-headed hammer and perhaps an adjustable spanner handy as this may help. Prepare the Work Area It is important that you assemble your product in a clean, clear, uncluttered area. -
Page 6: Safety
Safety Before you undertake any programme of exercise that will increase cardiovascular activity please be sure to consult with your doctor. Frequent strenuous exercise should be approved by your doctor and proper use of your product is essential. Please read this manual carefully before commencing assembly of your product or starting to exercise. -
Page 7: Exercise Information
Exercising Information Beginning How you begin to exercise will vary from person to person. If you have not exercised for a long period of time, have been inactive for a while, or are severely overweight you MUST start slowly, increasing your exercise time gradually, by perhaps only a few minutes for each session per week. - Page 8 Exercising Information Warm Up A successful exercise programme consists of three parts, Warm Up, Aerobic Exercise and Cool Down. Never start a training session without warming up. Never finish one without cooling down correctly. Perform between five and ten minutes of stretching before starting your workout to prevent muscle strains, pulls and cramps.
- Page 9 Exercising Information Target Zone (con't) USERS UNCONDITIONED CONDITIONED TARGET ZONE - A TARGET ZONE - B (Years) (Beats per Minute) (Beats per Minute) 20-24 145 - 165 155 - 175 25-29 140 - 160 150 - 170 30-34 135 - 155 145 - 165 35-39 130 - 150...
- Page 10 Exercising Information Shoulder Lif t Rotate and lift your right shoulder up towards your ear for one count. Relax then repeat for the left shoulder. Repeat 3 - 4 times. Calf / Achilles Stretch Turn towards the wall and place both hands on it. Support yourself with one leg while the other is placed behind you with the sole flat on the floor.
- Page 11 Exercising Information Basic Aerobic Training Programme For your basic Aerobic Exercise routine we suggest that you try the following. Remember, breathe correctly, exercise at your own pace and do not over-train as injury may result. Week 1 & 2 Exercise 4 minutes at 'A' Rest 1 minute Warm Up 5 - 10 Minutes Exercise 2 minutes at 'A'...
-
Page 12: Exercise Monitor
EXERCISE MONITOR USER INSTRUCTIONS Your Exercise Monitor has been specially designed to help you plan and view your exercise performance. MODE ESET MONITOR FUNCTION SPECIFICATIONS SCAN SHOWS EACH FUNCTION EVERY 4 SECONDS (CHANGING FROM FUNCTION TO FUNCTION) TIME 0.00 - 99.59 Minutes and Seconds (MINUTES AND SECONDS - COUNT UP / DOWN) SPEED 0.00 - 999.9 Kilometres per Hour... - Page 13 EXERCISE MONITOR USER INSTRUCTIONS BATTERY INSTALLATION fit the necessary BATTERIES - (NOT SUPPLIED) to your Exercise Monitor, remove the BATTERY COVER at the REAR r o t arefully fit the batteries by fitting between the exposed contacts in the battery compartment.
-
Page 14: Assembly & Adjustments
Assembly & Adjustments OPERATING ADJUSTMENTS and GENERAL USER INFORMATION Note LEVELLING THE CROSS TRAINER For security and stability, your 2-in-1 Cycle-Cross Trainer has Incorrect or excessive a factory welded frame and once fully assembled correctly, training may damage your should not need further alignment. However, in the interest of health. - Page 15 Assembly ACCESSORY FITMENT LIST These are all the accessories you will need to complete the assembly of your product. The following accessories are supplied in a pack and should be checked before attempting assembly. Item 51 Item 5 Item 6 Item 7 Qty 4 Qty 12...
- Page 16 Assembly Carefully unpack each component, checking against the parts list that you have all the necessary parts to complete the assembly of your product. Please note that some of the parts may be pre-fitted to major Beny Sports Co. UK Ltd components, so please check carefully before contacting our Unit 8, Riparian Way, CUSTOMER SUPPORT team.
- Page 17 Assembly A-1.Hold the Tension Cable-Lower (52) below the metal bracket. Guide the lower part of the inner cable of the Tension Cable-Upper (68) into the formed metal loop on the inner cable of the Tension Cable. A-2.Still holding the Tension Cable-Lower (52), pull the Tension Control Knob(71) inner cable away from the Metal Bracket (you will notice some resistance at this stage) and guide the inner cable through the open slot in the metal bracket.
- Page 18 Assembly Attach both Footplates (24 L/R) to the Footplate Support Bars (25 L/R) using 2 x M8 x50mm Hex Bolts (23), 2 x M8 Flat Washers (26) and 2 x Knob M8 (93) for each footplate. Note : The Footplates can be adjusted in three positions. Release the 3 x M8 Nylon Nuts (27) and 3 x M8 Flat Washers (26) from underneath of the Saddle (90), then attach the Saddle (90) to the Saddle Support (88) using the 3 x M8 Nylon Nuts...
- Page 19 Assembly i. Connect the Footplate Bars (25 L /R ) to the crank arms using 1 x Hex Bolt (9) , 1 x Spring Washer (6), 1 x Flat Washer (10) through the Footplate Support Bar(25 L/R), then fit 1 x M19 Wave Washer (13) with 1 x S13 Round Cap (8) into the crank arms for each side ii.
- Page 20 Assembly Secure Handlebar –Upper (3 L/R) into the appropriate Dual Action Handlebar-Lower (15 L/R) using 4 x M8 x 40mm Hex Bolts (4), 4 x M8 Curved Washers (5), 4 x M8 Spring Washers (6) and 4 x M8 Dome Nuts (7). Tighten the Fixed Handlebar (81) to the Handlebar Upright (70) using 2 x M8 x 30mm Allen Bolts (82), 2 x M8 Spring Washers (6) and 2 x M8 Curved Washers (26).Attach the Handlebar Cover (83) on to the back of the Fixed Handlebar (81).
- Page 21 Assembly Release the 2 x M5 x 12mm Screws (75) from the back of the Exercise Monitor (76). Connect the Monitor Link Wire (69) and Pulse Sensor Wire (80) to the Exercise Monitor (76), then fit the Exercise Monitor (76) onto the Exercise Monitor Bracket and secure using 2 x M5 x 12mm Screws (75) that were released.
- Page 22 Assembly 44 45 10 29 Page 22...
- Page 23 Assembly MASTER PARTS & ACCESSORY LIST Rear Stabilizer ....PART No. DESCRIPTION ....QTY M8 x75mm Carriage Bolt .
- Page 24 Beny Sports Co. UK Ltd. Unit 8 Riparian Way, The Crossings Business Park, Cross Hills, West Yorkshire BD20 7BW CUSTOMER SUPPORT Open from 9.00am to 5.00pm from Monday to Friday Tel: FREEPHONE (in the UK) 0800 3 101 202 +44 (0) 1535 637711 (outside the UK) E-mail: support@benysports.co.uk Website: www.benysports.co.uk ©...