User Responsibilities - C-TEC XFP501E/CA User Manual & Log Book

CAST XFP 16 & 32 ZONE ANALOGUE ADDRESSABLE FIRE ALARM PANEL

USER RESPONSIBILITIES

BS5839-1 is the British Standard code of practice for the design, installation, commissioning and maintenance
of fire detection and fire alarm systems for buildings. Section 7 of the standard (User Responsibilities) states
that a named responsible person should be appointed to supervise all matters pertaining to the fire alarm
system {clause 47.2a}.
Highlighted below is a summary of the main functions the responsible person is expected to carry out with
regard to BS5839-1 only. It does not highlight any other responsibilities that may be required of the user
or responsible person that are listed in documentation such as the Employers Guide to Fire Safety, the Fire
Precautions (Workplace) regulations and/or any other legislation relevant to the premises. If in doubt, the
fire authority can advise on the fire legislation that applies to any given building. For countries outside the
UK, different user responsibilities may apply.
BS5839-1 states the responsible person should:
(The bracketed numbers {xx} identify the BS5839-1 clauses to which the summary refers.)
1 Ensure the fire alarm panel is checked daily to confirm there are no faults on the system {47.2b}.
2 Ensure arrangements are in place for the test, maintenance and regular servicing of the system with
regard to Section 6 of the standard {47.2c}. Important: Clause 44 of BS5839-1 recommends weekly and
monthly tests that should be carried out by the responsible person. See below for details.
3 Ensure the Fire Alarm Log Book is kept up to date by recording fire signals, fault signals, work on the
system, etc., and make sure it is available for inspection at all times {47.2d / 48}.
4 Ensure all relevant occupants of the premises are instructed in the proper use of the system {47.2e}.
5 Take steps to limit the number of false alarms on the system {47f}.
6 Ensure the effectiveness of the system is not impaired by ensuring there is a space of at least 500mm
in all directions around and below every fire detector and that all manual call points are unobstructed
and easy to see {47g}.
7 Liaise with all relevant building engineers, decorators, etc., to ensure any changes to (or maintenance
of), the building's fabric does not compromise the protection given by the fire alarm system, create
faults or false alarms {47h}.
8 Ensure that any structural or occupancy changes planned for the building are done so with due and
early consideration given to any changes that may be required to the fire system {47h}.
9 Ensure that a selection of spare parts are held as appropriate within the premises {47j}.
Routine weekly testing to be undertaken by the user/responsible person
To meet the requirements of Clause 44 of BS5839-1 we recommend the following tests are carried out at
approximately the same time each week, during normal working hours:
Note: It is essential any alarm receiving centre is contacted before, and after, these tests to avoid unwanted
alarms and to confirm the fire signal is correctly received.
• Carry out an Indicator lamp test to check all zone lights show and the internal sounder activates.
• Operate a manual call point or automatic detector to test the fire alarm.
• Check that the alarm sounders operate.
• Reset the system by first pressing the Silence/Resound Sounders button and then pressing the Control
Panel Reset button.
• Verify that no manual call points or automatic detectors are obstructed in any way.
• Test a different zone each week using a different call point or detector so all zones are tested in rotation.
Routine monthly testing to be undertaken by the user/responsible person
Ensure authorised service personnel verify the system's standby power supply, or batteries, are in good
working order.
Quarterly and periodic inspection, testing, servicing and maintenance
It is the user's responsibility to ensure that an ongoing periodic plan is in place that meets Clause 45
(Inspection and Servicing) of BS5839-1. The work required to meet this Clause must be carried out by a
competent person with specialist knowledge of fire detection and alarm systems. The standard recognises
this will normally be an outside specialist fire alarm servicing organisation.
Note: The above summaries do not replace Sections 6 and 7 of BS5839-1 but are intended to help the user gain a greater understanding
of his or her responsibilities. We strongly recommend the named responsible person familiarises themselves with the full standard, copies
of which are available from the British Standards Institute, Customer Services Dept., 389 Chiswick High Road, London, W4 4AL. Tel: +44
(0)20 8996 9001. Web: www.bsi-global.com.
USER MANUAL & LOG BOOK • Approved Document No. DFU5020000 Rev 3 • Page 5 of 24