Settings Menu - Rotel A12MKII Owner's Manual

14

Settings Menu

You can access the SETUP menu from the front panel by pressing the MENU
9
button or the K button on the remote. You can change the value of
the selected option by pressing the - or + buttons on the front panel or the
up/down/left/right C arrow buttons on the remote. Step through the
sub-menus by pressing the MENU
button on the remote.
• TONE BYPASS: TONE BYPASS on/off (For more information refer to Tone
Control Bypass section).
NOTE: This setting is stored permanently even after the A12MKII is
powered off.
• BASS: BASS level can be changed to desired settings. (For more information
refer to Bass and Treble Control section.)
NOTE: This setting is stored permanently even after the A12MKII is
powered off.
• TREBLE: TREBLE level can be changed to desired settings. (For more
information refer to Bass and Treble Control section.)
NOTE: This setting is stored permanently even after the A12MKII is
powered off.
• BALANCE: Change left/right balance. (For more information refer to
Balance Control section.)
NOTE: This settings is stored permanently even after the A12MKII is
powered off.
• DIMMER: Dims the front display.
NOTE: This setting is stored permanently even after the A12MKII is
powered off.
• LED DIMMER: Dims the Power LED and the LEDs above the Speaker Selector
buttons on the front panel.
NOTE: This setting is stored permanently even after the A12MKII is
powered off.
• POWER ON MAX VOL: This sets the maximum volume level when the unit
is turned on. "45" is the factory default.
NOTE: Power On Max Volume settings do not apply to sources
configured with Fixed Gain.
• USB POWER: This option allows the rear panel USB connector to provide
power, even when the A12MKII is in standby mode.
To enable the continuous power mode, select the ALWAYS option. To provide
power only when the A12MKII is powered on, select the NORMAL option.
The default for USB POWER is set to NORMAL.
NOTE: The front panel power button must be in the ON position to
supply power to the rear panel USB connector.
9
button on the front panel or the
NOTE: When the USB POWER is configured to ALWAYS the A12MKII
will consume additional power in standby mode to supply USB power.
NOTE: Due to local power consumption regulations the USB POWER
function is not available in all markets.
K • OFF TIMER: The A12MKII can be configured to automatically power off if
unused for a specified period. If no changes are made to the unit within
the specified "Off Timer" period the unit will automatically go to STANDBY
mode. The Auto Power Off timer will be restarted if changes are made to
the volume, source or playback. The default for Off Timer is set to 20 MINS.
Valid settings include: 20MINS (Default), DISABLE, 1 HOUR, 2 HOURS,
5 HOURS, 12 HOURS.
• SIGNAL SENSE: Check if an audio signal is present on the configured
Signal Sense input. The A12MKII monitors the data stream to determine if
there is audio. If there is no audio detected for 10 minutes, the A12MKII
will enter Signal Sense Power Mode. When in Signal Sense Power
Mode and the A12MKII detects audio on Signal Sense input, the unit will
automatically power on. When Signal Sense is set to AUTO the A12MKII
will monitor the Coax, Optical and Bluetooth sources and if a signal is
detected on any of these inputs the unit will power on and select that input
as the active source. To disable this function, select the OFF option which
is the factory default setting.
NOTE: When the SIGNAL SENSE function is activated the A12MKII
will consume additional power in signal sense standby mode.
NOTE: Due to local power consumption regulations the SIGNAL SENSE
function is not available in all markets.
• FIXED GAIN: Configures a Fixed Volume level for a specified input. To
enable this feature, select the desired fixed volume level for AUX1, AUX2,
USB, PC-USB, Optical 1, Optical 2, Coax 1, Coax 2, or Bluetooth. When
enabled and the input with a Fixed Volume is selected, the Volume level
will immediately be set to the specified level.
Valid settings include: VARIABLE, FIXED MIN, FIXED 01-95, FIXED MAX.
• AUX1 VOL: VARIABLE (disabled) is factory default.
• AUX2 VOL: VARIABLE (disabled) is factory default.
• USB VOL: VARIABLE (disabled) is factory default.
• PC-USB VOL: VARIABLE (disabled) is factory default.
• OPT1 VOL: VARIABLE (disabled) is factory default.
• OPT2 VOL: VARIABLE (disabled) is factory default.
• COAX1 VOL: VARIABLE (disabled) is factory default.
• COAX2 VOL: VARIABLE (disabled) is factory default.
• BTOOTH VOL: VARIABLE (disabled) is factory default.
NOTE: The Volume knob on the front panel and Volume +/- buttons
on the IR remote are disabled when the volume is Fixed. To disable this
feature set the Fixed Volume level to "Variable".
A12MKII Stereo Integrated Amplifier