Table of Contents
Advertisement
14
Network Connection o
The A14MKII can be attached to a network using the rear panel NETWORK
o
socket
. The NETWORK configurations allow both STATIC and DHCP
IP addressing. See the Network section of this manual under Setting Menu
for IP address configuration information.
The NETWORK connection allows software updates to be downloaded from
the Internet. The NETWORK connection also allows IP control for integration
with automation systems.
For additional information on the IP control please contact your authorized
Rotel dealer.
Settings Menu
You can access the SETUP menu from the front panel by pressing the MENU
9
button or the
button on the remote. You can change the value of
K
the selected option by pressing the - or + buttons on the front panel or the
up/down/left/right
arrow buttons on the remote. Step through the
C
sub-menus by pressing the MENU
button on the remote.
• TONE BYPASS: TONE BYPASS on/off (For more information refer to Tone
Control Bypass section).
NOTE: This setting is stored permanently even after the A14MKII is
powered off.
• BASS: BASS level can be changed to desired settings. (For more information
refer to Bass and Treble Control section.)
NOTE: This setting is stored permanently even after the A14MKII is
powered off.
• TREBLE: TREBLE level can be changed to desired settings. (For more
information refer to Bass and Treble Control section.)
NOTE: This setting is stored permanently even after the A14MKII is
powered off.
• BALANCE: Change left/right balance. (For more information refer to
Balance Control section.)
NOTE: This settings is stored permanently even after the A14MKII is
powered off.
• DIMMER: Dims the front display.
NOTE: This setting is stored permanently even after the A14MKII is
powered off.
• LED DIMMER: Dims the Power LED and the LEDs above the Speaker Selector
buttons on the front panel.
NOTE: This setting is stored permanently even after the A14MKII is
powered off.
• POWER ON MAX VOL: This sets the maximum volume level when the unit
is turned on. "45" is the factory default.
9
button on the front panel or the
NOTE: Power On Max Volume settings do not apply to sources
configured with Fixed Gain.
• POWER MODE: Enables the A14MKII to be controlled via the network
port when attached to an automation system. The power consumption is
higher in Quick Power mode. If network control is not required select the
Normal Power mode. "Normal" is the factory default.
Valid settings include: Quick, Normal.
NOTE: When the POWER MODE is configured to Quick, the A14MKII
will consume additional power in standby mode.
NOTE: Due to local power consumption regulations the POWER MODE
function is not available in all markets.
• USB POWER: This option allows the rear panel USB connector to provide
power, even when the A14MKII is in standby mode.
To enable the continuous power mode select the ALWAYS option. To provide
power only when the A14MKII is powered on, select the NORMAL option.
The default for USB POWER is set to NORMAL.
K
NOTE: The front panel power button must be in the ON position to
supply power to the rear panel USB connector.
NOTE: When the USB POWER is configured to ALWAYS the A14MKII
will consume additional power in standby mode to supply USB power.
NOTE: Due to local power consumption regulations the USB POWER
function is not available in all markets.
• OFF TIMER: The A14MKII can be configured to automatically power off if
unused for a specified period. If no changes are made to the unit within the
specified "Off Timer" period, the unit will automatically go to STANDBY
mode. The auto power off timer will be restarted if changes are made to the
volume, source or playback. The default for Off Timer is set to 20 MINS.
Valid settings include: 20MINS (Default) DISABLE, 1 HOUR, 2 HOURS, 5
HOURS, 12 HOURS.
• SIGNAL SENSE: Check if an audio signal is present on the configured
Signal Sense input. The A14MKII monitors the data stream to determine if
there is audio. If there is no audio detected for 10 minutes, the A14MKII
will enter Signal Sense Power Mode. When in Signal Sense Power
Mode and the A14MKII detects audio on Signal Sense input, the unit will
automatically power on. To disable this function, select the OFF option
which is the factory default setting.
NOTE: When the SIGNAL SENSE function is activated the A14MKII
will consume additional power in signal sense standby mode.
NOTE: Due to local power consumption regulations the SIGNAL SENSE
function is not available in all markets.
• FIXED GAIN: Configures a Fixed Volume level for a specified input. To
enable this feature, select the desired fixed volume level for AUX1, AUX2,
USB, PC-USB, Optical 1, Optical 2, Coax 1, Coax 2, or Bluetooth. When
enabled and the input with a Fixed Volume is selected, the Volume level
will immediately be set to the specified level.
A14MKII Stereo Integrated Amplifier
Advertisement
Table of Contents
