Techni Sport TSC81 Assembly Instructions

ASSEMBLY INSTRUCTIONS
Backrest Seat Left Armrest
A A B B C-L C-L
Note: When sitting on chair, not looking at it
J-N Neck pillow J-L Lumbar pillow Allen wrench
K
Except TS84
STEP
Insert the casters Ⓗ into the legs of the base Ⓖ using
1
pressure, then place the gas lift Ⓔ in the middle of the
base and cover it with Ⓕ.
Ⓕ
Ⓔ
Ⓗ
STEP
Put the seat over the base parts making sure the tip of
4
the gas lift enters into the hole of the mechanism, then
assemble the backrest Ⓐ to the metal brackets on
both sides of the seat Ⓑ using screws Ⓜ, O-rings Ⓞ
and washers Ⓟ.
ⓄⓅ
Ⓜ
O-Ring in
the middle!

GAMING CHAIRS MODELS

TS83, TS84, TS90, TS92,
TSF44, TSC81, XXL2
Right Armrest Mechanism
C-R D D
L M8x20mm, M8x25mm,
M
4 pcs 12 pcs
(Mechanism)
(Backrest, armrest)
Turn over the seat Ⓑ with its back end towards you, as shown
STEP
below. Place
2
screws Ⓛ, O-rings Ⓞ and washers Ⓟ to install the
mechanism Ⓓ with its knob facing towards the front.
Ⓓ
Ⓖ
Ⓑ
(Front)
STEP
Attach the covers
5
respective sides of the seat Ⓑ using screws Ⓝ and
cover the holes with Ⓠ As shown.
Ⓐ
R Ⓝ
R
Ⓑ
ATTENTION:
⚠ Follow the instructions step by step.
⚠ To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places.
⚠ Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.
⚠ Using the wrong size of screws on a part could result in damage to the screw or the part.
Gas Lift Covers for gas
E E F F
lift, set of 3 pcs
M5x12mm, O-Rings,
N O
16 pcs
2 pcs
(Brackets Covers)
on the four seat mechanism holes. Use
Ⓠ
4 sets
Ⓛ
Ⓞ
Ⓟ
O-Ring in
the middle!
(Back)
4 pcs
Ⓠ
and to the brackets on their
I-L I-R
I-L
I-R
LEFT
RIGHT
Ⓑ
5-leg star base Casters, 5 pcs.
G G H H I-L Left cover for
seat bracket
felt gaskets,
Washers, Hole Covers,
P Q R
16 pcs 4 pcs
4 pcs
R
STEP
Assemble the armrests
C-L
3
sides of the seat Ⓑ using screws Ⓜ, O-rings Ⓞ and
washers Ⓟ.
C-R C-R
RIGHT RIGHT
Ⓓ
(Back)
Note: The armrest side is determined by you sitting on the chair, not looking at it
STEP
First attach the lumbar pillow
6
by fastening the buckles behind the backrest Ⓐ as
J-N
shown.
J-N
J-L
Right cover for
I-R
seat bracket
and in their respective
C-R
8 sets
Ⓜ
Ⓞ
Ⓟ
C-L
O-Ring in
LEFT
the middle!
Ⓑ
then the neck pillow
J-L
Ⓐ
(This shows
The chair
from behind)