Techni Sport TS42 Assembly Instructions

ASSEMBLY INSTRUCTIONS
Backrest Seat
A B C-L
Right cover for Neck pillow *
I-R J-N J-L
seat bracket
* The shape of these 2 pieces varies on each model.
* TS61 & TS62C don't not come with lumbar pillow.
STEP
Insert the casters Ⓗ into the legs of the base
1
Ⓖ using pressure, then place the gas lift Ⓔ in
the middle of the base and cover it with Ⓕ.
Ⓕ
Ⓔ
Ⓖ
Ⓗ
STEP
Put the seat over the base parts making sure the tip of
4
the gas lift enters into the hole of the mechanism, then
assemble the backrest Ⓐ to the metal brackets on
both sides of the seat Ⓑ using screws Ⓜ, O-rings Ⓞ
and washers Ⓟ.
Ⓞ Ⓟ
Ⓜ
O-Ring in
the middle!
GAMING CHAIR RTA MODELS
TS42, TS43,
TS50, TS51, TS52,
TS60, TS61, TS62C, TS63C.
Left Armrest Right Armrest
C-R D
* When sitting on chair, not looking at it
Allen wrench
Lumbar pillow * L
K
STEP
Flip over the seat Ⓑ with its back end towards you, peel and place
2 the felt gasket Ⓛ over the holes on the seat, and using screws Ⓛ,
O-rings Ⓞ and washers Ⓟ, assemble the mechanism Ⓓ with its
handle facing to the LEFT as shown.
IMPORTANT:
Felt gasket goes
over the seat's
hole!
STEP
Attach the covers
5
respective sides of the seat Ⓑ using screws Ⓝ and
cover the holes with Ⓠ As shown.
Ⓐ
Ⓠ Ⓝ
Ⓑ
ATTENTION:
⚠ Follow the instructions step by step.
⚠ To avoid misalignments, leave the screws loose and do not tighten them until all are in their respective places.
⚠ Do not overtighten or force the screws as they could break, strip, or damage the threads of the holes.
⚠ Using the wrong size of screws on a part could result in damage to the screw or the part.
Mechanism Gas Lift Covers for gas
E F
lift, set of 3 pcs
M8x20mm with M8x25mm, M6x12mm,
M
N
felt gasket, 12 pcs 2 pcs
4 pairs.
(Mechanism) (Armrest, Backrest) (Brackets Covers)
4 sets:
Ⓑ
O-Ring in
Ⓓ
the middle!
(Back)
and to the brackets on their
I-L I-R
I-L
I-R
LEFT
RIGHT
Ⓑ
5-leg star base Casters, 5 pcs.
G H
O-Ring, Washers,
O P
16 pcs 16 pcs
STEP
Assemble the armrests
3
sides of the seat Ⓑ using screws Ⓜ, O-rings Ⓞ and
washers Ⓟ.
Ⓛ
Ⓞ
C-R
Ⓟ
RIGHT
(Back)
Note: The armrest side is determined by you sitting on the chair, not looking at it
STEP
For pillows with straps, first attach the lumbar pillow
6
then the neck pillow
J-N
behind the backrest Ⓐ as shown.
J-N
*
J-L
(*) Except TS61 and TSC62C
Left cover for
I-L
seat bracket
Hole covers,
Q
2 pcs
and in their respective
C-L C-R
8 sets:
Ⓜ
Ⓞ
Ⓟ
C-L
O-Ring in
LEFT
the middle!
Ⓑ
J-L
by fastening the buckles
Ⓐ
(This shows
The chair
from behind)