Selecting Default Configuration - "Def; Power-Up Test Setting - "Put; Buzzer Setting - "Buz; Alarm Relay Configuration - "Arc - Macurco RD-6 User Instructions

Macurco RD-xx User Manual
4.4.1 Selecting Default Configuration – "dEF"
To select the Default Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then
push the Enter button to enter the Con menu. The first selection is the "dEF" or Default setting. Push Enter. If it is already in
Default configuration, there will be no action. If it is not already in Default configuration, "nO" will be displayed. Push Next to
change it to "yES" (flashing) then push Enter to confirm the change (solid) and push Enter again to return to "dEF" in the con
menu. Push Next until "End" is displayed then push Enter to get back to normal operation.
Note: "dEF" menu cannot be changed during calibration due warning and calibration overdue trouble. Refer to Section 4.5.13
Calibration Period Settings – "CAL" for Calibration Due Warning and Calibration Overdue trouble.
4.4.2 Power-Up Test Setting – "PUt"
To select the Power Up Test Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu.
Then push the Enter button to enter the Con menu. Then push the Next button to get to the second selection "PUt" or Power
Up Test setting. Push Enter. If the test is "On" push Next to turn it "OFF" (flashing) then push Enter to confirm the change (solid)
and push Enter again to return to "PUt" in the Con menu. Push Next until "End" is displayed then push Enter to get back to
normal operation.
4.4.3 Buzzer Setting – "bUZ"
To select the Buzzer Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then push
the Enter button to enter the Con menu. The third selection is the "bUZ" or Buzzer setting. Push Next twice to get to "bUZ" then
Enter. If the display is "On" push Next to turn it "OFF" (flashing) then push Enter to confirm the change (solid) and push Enter
again to return to "bUZ" in the Con menu. Push Next until "End" is displayed then push Enter to get back to normal operation.
4.4.4 Alarm Relay Configuration – "Arc"
To select the Alarm Relay Configuration, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then
push the Enter button to enter the Con menu. The fourth selection is the "Arc" or Alarm Relay Configuration. Push Next three
times to get to "Arc" then Enter. If the relay is "nO" (normally open) push Next to turn it to "nC" (flashing) then push Enter to
confirm the change (solid) and push Enter again to return to "Arc" in the Con menu. Push Next until "End" is displayed then
push Enter to get back to normal operation.
4.4.5 Fan Relay Delay Setting – "Frd"
To select the Fan Relay Delay setting, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then
push the Enter button to enter the Con menu. The fifth selection is the "Frd" or Fan Relay Delay. Push Next four times to get to
"Frd" then Enter. If the delay is "0" (zero minutes) push Next to change it to 1, 3, 5, or 10 minutes (flashing) then push Enter to
confirm the change (solid) and push Enter again to return to "Frd" in the Con menu. Push Next until "End" is displayed then
push Enter to get back to normal operation.
4.4.6 Fan Relay Minimum Runtime Setting – "Frr"
To select the Fan Relay Minimum Runtime setting, in normal mode, push the Next button to get to "Con" or the Configuration
menu. Then push the Enter button to enter the Con menu. The sixth selection is the "Frr" or Fan Relay Minimum Runtime. Push
Next five times to get to "Frr" then Enter. If the runtime is "0" (zero minutes) push Next to change it to 3, 5, 10 or 15 minutes
(flashing) then push Enter to confirm the change (solid) and push Enter again to return to "Frr" in the Con menu. Push Next until
"End" is displayed then push Enter to get back to normal operation.
4.4.7 Fan Relay Latching Setting – "FrL"
To select the Fan Relay Latching Option, in normal mode, push the Next button to get to "Con" or the Configuration menu. Then
push the Enter button to enter the Con menu. The seventh selection is the "FrL" or Fan Relay Latching Option. Push Next six
times to get to "FrL" then Enter. If latching is "OFF" push Next to turn it to "On" (flashing) then push Enter to confirm the
change (solid) and push Enter again to return to "FrL" in the Con menu. Push Next until "End" is displayed then push Enter to
get back to normal operation.
19 |
REV – 2.1 [34-2900-0511-7 ] P a g e