Table of Contents
Advertisement
Contents of P2 card status display settings
Select [PROPERTY] → [CARD STATUS] from the thumbnail menu. The following screen appears.
r When [REMAIN] is selected
1
5
4
1 Write-protect mark
The [
] mark appears if the P2 card is write-protected.
2 P2 card status (remaining capacity)
The remaining memory capacity of the P2 card is shown as a bar
graph and percentage. The bar graph indicator moves to the left as
the remaining capacity decreases.
The following displays may appear, depending on the card status.
[FORMAT ERROR!]
An unformatted P2 card is inserted.
[NOT SUPPORTED!]
An unsupported card is inserted in the
camera.
[NO CARD]
No P2 card is inserted.
Use the cursor buttons to place the cursor on the P2 card for data
to be accessed and press the <SET> button to display detailed
information about the P2 card to check specific information such as
the serial number and the user ID.
3 P2 card remaining capacity/total capacity
Displays the P2 card remaining capacity and total capacity. The units
are minutes. Because only the figures in minutes are displayed, the
total remaining memory capacity for each P2 card may not match the
total remaining memory capacity.
4 Total remaining capacity for the slot
Displays the total remaining capacity for all two slots.
However, the remaining capacity of a write-protected P2 card is not
included in the total available space.
5 Warning mark
When the following P2 cards are detected, the [
[RUN DOWN CARD]
The maximum number of overwrites on the
P2 card has been exceeded.
[DIR ENTRY NG CARD]
The directory structure on the P2 card is not
supported.
The warning can be confirmed on the P2 card detailed information
display in "P2 card status (remaining capacity)" (page 114).
SD memory card status display
The status display enables confirmation of the SD memory card format condition, available memory space, etc.
Select [PROPERTY] → [DEVICES] → [SD CARD] from the thumbnail menu.
[SD STANDARD]
Indicates whether an SD memory card is formatted according to the SD/SDHC standard.
f [SUPPORTED]: Complies with SD/SDHC
f [NOT SUPPORTED]: Does not comply with SD/SDHC
[USED]
Used capacity (bytes)
[BLANK]
Available space (bytes)
[TOTAL]
Total capacity (bytes)
[PROXY REM]
Remaining capacity in proxy recording (displayed only when the video encoder board is installed)
[NUMBER OF CLIP]
The number of clips on an SD memory card when clips have been copied to an SD memory card
[PROTECT]
Write protected
Chapter 6 Thumbnail Operations for Clips — Thumbnail operations
2
] mark is displayed.
r When [USED] is selected
1
3
5
4
1 Write-protect mark
The [
] mark appears if the P2 card is write-protected.
2 P2 card status (used memory capacity)
The used memory capacity of the P2 card is shown as a bar graph
and percentage. The bar graph indicator moves to the right as the
used memory capacity increases.
The following displays may appear, depending on the card status.
[FORMAT ERROR!]
[NOT SUPPORTED!]
[NO CARD]
Use the cursor buttons to place the cursor on the P2 card for data
to be accessed and press the <SET> button to display detailed
information about the P2 card to check specific information such as
the serial number and the user ID.
3 P2 card used memory capacity/total capacity
Displays the P2 card used memory capacity and total capacity. The
units are minutes. Because only the figures in minutes are displayed,
the total used memory capacity for each P2 card may not match the
total memory capacity.
The used memory capacity of a write-protected P2 card is displayed
as 100%.
4 Total used memory capacity for all slots
Displays the total used memory capacity for all two slots.
5 Warning mark
When the following P2 cards are detected, the [
[RUN DOWN CARD]
[DIR ENTRY NG CARD]
The warning can be confirmed on the P2 card detailed information
display in "P2 card status (used memory capacity)" (page 114).
– 114 –
2
An unformatted P2 card is inserted.
An unsupported card is inserted on the
camera.
No P2 card is inserted.
] mark is displayed.
The maximum number of overwrites on the
P2 card has been exceeded.
The directory structure on the P2 card is not
supported.
3
Advertisement
Table of Contents
