Summary of Contents for Member's Mark GR2210601-MM-00
Page 1
STAINLESS STEEL AND PORCELAIN 5-BURNER GAS GRILL Model number: GR2210601-MM-00 ASSEMBLY & OPERATING INSTRUCTIONS For Outdoor Use Only This instruction manual contains important information necessary for the proper assembly and safe use of the appliance. Read and follow all warnings and instructions before assembling/using the appliance.
WARNINGS SAFETY LABELS DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Be alert to the possibility of serious bodily injury if the instructions are not followed. Be sure to read and carefully follow all of the messages. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
Page 3
WARNING This outdoor cooking gas appliance shall be used only outdoors and shall not be used in a building, garage or any other enclosed area. This outdoor cooking gas appliance is not intended to be installed in or on boats. This appliance is not intended to be installed in or on recreational vehicles.
USE AND INSTALLATION OF LP GAS CYLINDER (PROPANE TANK) BEFORE INSTALLING: The installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2, or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV Series, Recreational Vehicle Code, as applicable.
Page 5
DANGER DO NOT connect this grill to an existing #510 POL cylinder valve with Left hand threads. The Type 1 valve can be identified with the large external threads on the valve outlet. DO NOT connect to a propane cylinder exceeding its capacity. ...
INSTALLING GAS CYLINDER 1. Check that the cylinder valve is closed by turning the knob in clockwise. 2. Pull out the cylinder holder along the slot. 3. Place the cylinder into cylinder holder and tighten the fixing bolt. Place cylinder such that the valve opening faces the side burner in such a way that the hose is not kinked/damaged.
CONNECTION PROCEDURES Make sure the tank valve is closed (turn valve clockwise until tight). Check the tank valve to insure it has the proper external male threads. Make sure all burner valves are turned OFF. Inspect valve connections, port, and regulator assembly.
25. Right Cart Assembly 26. Locking Caster Qty: 1pc Qty: 4pcs HARDWARE LIST Item No. Item name Diagram Phillips Head Screwdriver M4x10mm Bolt (Black) M6x12mm Bolt (Black) Hex Nut Wrench M4x10mm Bolt (Silver) M6x12mm Bolt (Silver) LR6/AA Battery M4x8mm Bolt Note: Hardware H has been pre-attached on the related components.
Page 12
Replacement Part List (I) 12 of 36 20151113-Ver1...
Page 13
Replacement Part List (II) Part Part Name Part Part Name Number Number Warming Rack Cooking Grate Flame Tamer Grill Body Assembly Grill Body – Lid Grill Body – Thermometer Grill Body – Thermometer Bezel Grill Body – Lid Handle Bezel Grill Body –...
Page 14
Tank Fixing Screw Tank Locking Plate Rear Cart Assembly Rear Cart Panel Rear Cart Frame Match Holder Bottom Cart Panel Right Cart Side Panel Front Cart Assembly Front Cart Frame Door Magnet Fixing Plate Cart Frame Connecting Tube Door Handle Left Door Assembly Left Door Door Hinge...
ASSEMBLY PROCEDURES Step 1 Connect the Front Cart Assembly (20) and Rear Cart Assembly (17) with 4 pcs Cart Frame Connecting Tube (21) then secure them with 8 pcs M6x12 Bolts Black (C). Do not fully tighten the bolts. Step 2 Attach the Left Cart Side Panel Assembly (14) to the cart assembly using 4 pcs M6x12 Bolts Black (C).
Page 16
Step 3. Attach the Right Cart Panel (19) to the cart assembly using 4 pcs M6x12 Bolts Black (C). Do not fully tighten the bolts. Step 4 Attach the Bottom Cart Panel (18) to the cart assembly using 10 pcs M6x12 bolts Black (C).
Page 17
Step 5 nsert the Locking Casters (26) into the threaded holes on the bottom of the cart assembly. Use the Hex Nut Wrench (D) to tighten the caster by turning in clockwise until it is fully secured. Step 6 Lock all 4 locking casters to prevent the unit moving by stepping the pad downwards.
Page 18
Step 7 Attach the Left Door Assembly (23) and Right Door Assembly (25) to the cart assembly using 8 pcs M4x10 bolts Silver (E). Step 8 Attach the Door Handles (22) to the doors with the Plastic Inserts (24) using 4 pcs M6x12 bolts Silver (F) as shown. 18 of 36 20151113-Ver1...
Page 19
Step 9 Attach the Tank Heat Shield (15) to the cart assembly using 4 pcs M4x10 bolts Black (B). Step 10 This step needs two people to complete! Put the Grill Body assembly (4) carefully on top of the cart assembly. Secure the part in place as shown below with 4 pcs of M6x12mm bolts Silver (F) as shown.
Page 20
Step 11 Attach the Side Table Panel Assembly (11) to the Side Table Assembly (10) using 2 pcs M6x12mm bolts Silver (F). Step 12 Loosen 4 pcs pre-attached bolts M6x12mm bolts Silver (F) on the right side of the grill body and adjust to 3/16” clearance as shown. Position the holes on the side table assembly through the bolts at grill body as shown below.
Page 21
Step 13 Attach the Side Burner Control Panel (7) to the Side Burner Assembly (6) using 2 pcs M6x12mm bolts Silver (F). Step 14 Loosen 4 pcs pre-attached bolts M6x12mm bolts Silver (F) on the left side of the grill body and adjust to 3/16” clearance as shown. Position the holes on the side burner assembly through the bolts at grill body as shown below.
Page 22
Step 15 Remove the 2 pcs pre-assembled bolts M4x8mm (H) from the side burner valve and insert the valve outlet (orifice) into the side burner port. Then attach the valve to the Side Burner Control Panel. Fix the side burner valve onto the Control Knob Bezel (8) using 2 pcs removed bolts M4x8mm (H).
Page 23
Step 16: Insert the connector of the ignition wire to the terminal of the ignition electrode on the side burner assembly, as shown below. Insert the Control Knob / Side Burner Control Knob (9) to the pin on the side burner valve.
Page 24
Step 18: Slide the Grease Cup (12) into the holding bracket at the bottom of the drip tray. Be sure the handle is facing outward. Step 19: Place the Warming Rack (1), Cooking Grates (2), Flame Tamer (3) and Side Burner Grate (5) on the grill as shown. 24 of 36 20151113-Ver1...
Page 25
Step 20. Install a LR6/AA Battery (G) into the igniter. Step 21. Your unit is fully assembled! Make sure to read and follow the Instruction Manual before using this appliance. 25 of 36 20151113-Ver1...
LEAK TEST GENERAL Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive pressure unknowingly being applied to the unit. Periodically check the entire system for leaks following the procedures listed below.
3. If a leak is present, immediately turn off the gas supply and tighten the leaky fittings. 4. Turn the gas back on and recheck. 5. Should gas continue to leak from any of the fittings, turn off the gas supply and contact customer service department at (888) 837-1380, 8 a.m.
Page 28
To turn burners off, turn the control knobs clockwise until they lock in the OFF position. USING MATCH HOLDER TO LIGHT BURNER Turn OFF all burner valves. Make sure the lid is open. Place a lighted match on the match holder and hold next to the burner. You can either keep the match holder attached at the grill or take it off to light the burner at shown below.
FLAME CHARACTERISTICS This procedure outlines how to check for proper burner flame characteristics. Burner flames should be blue and stable with little yellow tips, with no excessive noise, or lifting. If the flame is yellow, it indicates insufficient air. If the flame is noisy and tends to lift away from the burner, it indicates too much air.
Spiders and small insects occasionally spin webs or make nests in the grill burner tubes during transit and warehousing. These webs can lead to gas flow obstruction that could result in a fire in and around burner tubes. This type of fire is known as flashback and can cause serious damage to your grill and create an unsafe operating condition for the user.
MAIN BURNER REPLACEMENT 1. Remove the flame tamer. 2. Remove the burner cotter pin as shown. 3. Remove the carry over and the burner fixing pin. 4. Remove the burner from the grill body. Step 2 Step 4 TO REINSTALL THE MAIN BURNERS: 1.
Page 32
SIDE BURNER REPLACEMENT 1. Open the side burner lid and remove the side burner grate. 2. Remove the burner fixing nut at the bottom of side burner assembly as shown. 3. Loose the side burner hook from the side burner port as shown. 4.
Page 33
WOOD CHIP TRAY OPERATION INSTRUCTIONS 1. Soak the wood chips in water for 1 hour prior to use. 2. Pull out the wood chip tray from the grill body as shown. 3. Open the wood chip tray cover and place the soaked wood chips into the tray. 4.
Page 34
CAUTION The wood chip tray and lid get very hot. Avoid handling them while in use. Always wear protective oven mitts when handling hot components. Cooking Tip – Flavoring wood: Small wood chips work best inside the wood chip box. ...
TROUBLE SHOOTING Problem: Possible Causes: Corrective Actions: Burner will not 1. LP cylinder fuel is used up. 1. Change a new full LP cylinder. light 2. Bad electrode spark. 2. Check to see if the spark will light 3. Burner properly using a match.
LIMITED WARRANTY Manufacturer warrants this Product to be free from defects in workmanship and materials for a period of Ninety (90) days from the date of purchase, PROVIDED claims are submitted, in writing, with proof of purchase. If any part of this item fails because of a manufacturing defect within the Limited Warranty Period, Manufacturer offers to replace such part(s) provide that such parts have not been improperly repaired, altered, or tampered with or subject to misuse, abuse or exposed to corrosive conditions.
Need help?
Do you have a question about the GR2210601-MM-00 and is the answer not in the manual?
Questions and answers