Advertisement
Quick Links
The Fujitsu Limited reorganized its LSI business into a wholly owned subsidiary, the Fujitsu
Microelectronics Limited on March 21, 2008.
The corporate names "Fujitsu" and "Fujitsu Limited" described all in this document have been
revised to the "Fujitsu Microelectronics Limited". Thank you for your cooperation and
understanding this notice.
Moreover, there are no changes in the related documents other than corporate names revised.
Customers are advised to consult with sales representatives before ordering.
Corporate names revised in the documents
March 21, 2008
Fujitsu Microelectronics Limited
Advertisement
Related Manuals for Fujitsu LQFP-176P
Summary of Contents for Fujitsu LQFP-176P
- Page 1 Corporate names revised in the documents The Fujitsu Limited reorganized its LSI business into a wholly owned subsidiary, the Fujitsu Microelectronics Limited on March 21, 2008. The corporate names “Fujitsu” and “Fujitsu Limited” described all in this document have been revised to the “Fujitsu Microelectronics Limited”.
- Page 2 FUJITSU SEMICONDUCTOR SS01-71080-1E SUPPORT SYSTEM DSU-FR EMULATOR LQFP-176P HEADER TYPE5 MB2198-703-E OPERATION MANUAL...
- Page 3 *1 : The package is the FPT-176P-M07 (lead pitch: 0.5mm, body size: 24.0mm × 24.0mm). *2 : FR is an abbreviation of FUJITSU RISC CONTROLLER and is a product of Fujitsu Limited. *3 : Referred to below as the “emulator”...
- Page 4 (i.e., submersible repeater and artificial satellite). Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.
-
Page 5: Check Package Contents
1. Check Package Contents Before starting to use the header board, check that all of the following items are present. • LQFP-176P header type5* • Header board attachment screws (M2 × 10mm, 0.4mm pitch) • Washers • NQPACK176SD* • HQPACK176SD* •... - Page 6 3. Notes on Designing ■ Notes on Designing the Printed Circuit Board for the User System If the header board is connected to a user system, the heights of parts mounted around the header board are restricted. When designing the printed circuit board of the user system, consider the heights of components within the range of the header board, as shown in Figure 1, so that the components mounted on the user system do not interfere with the header board.
- Page 7 ■ Notes for Designing the MCU Foot Pattern Figure 2 shows the recommended dimensions of the NQPACK footprint mounted on the printed cir- cuit board of the user system. The printed circuit board of the user system must be designed with due consideration given to this footprint as well as to the mass production MCU.
- Page 8 4. Procedure for Connecting to the User System Mount the supplied NQPACK on the user system before using the header board. ■ Connection Procedure 1. To connect the header board to the user system, align the index mark (the cut-out corner) on the header board with pin 1 on the NQPACK mounted on the user system, which is also indicated by an index mark (▲), and insert the header into the NQPACK (See Figure 3).
- Page 9 Header board attachment screws Header board Washers YQPACK User system NQPACK Figure 4 Header board connection procedure ■ Disassembly Procedure To remove the header board, first remove the four screws and then lift the header board vertically up and off of the NQPACK.
- Page 10 5. Connecting to the Adapter Board The adapter board and header board are connected by flat cables that are supplied with the adapter board. The flat cable connector C on the adapter board is not needed in this product (see Figure 5). ■...
- Page 11 6. Mounting a Mass Production MCU Use the supplied HQPACK to mount a mass production MCU on the user system. ■ Mounting 1. Align the index mark on the mass production MCU (●) with the index mark on the NQPACK mounted on the user system (▲), and then insert the mass production MCU.
-
Page 12: Connector Pin Assignment
7. Connector Pin Assignment Tables 1, 2 show the correspondence between the pin numbers for flat cable connectors A and B, the evaluation MCU on the adapter board, and the mass production MCU. For details on the mass production MCU pins, refer to the data sheet or hardware manual of each MCU. - Page 13 Table 1 Pin Assignment of Flat Cable Connector A Connector Evaluation MCU Mass production Connector Evaluation MCU Mass production pin number pin number MCU pin number pin number pin number MCU pin number AD11 AE11 AF11 AA12 AB12 AC12 AD12 AE12 AF12 AA13...
- Page 14 Table 2 Pin Assignment of Flat Cable Connector B Connector Evaluation MCU Mass production Connector Evaluation MCU Mass production pin number pin number MCU pin number pin number pin number MCU pin number AC10 AE10 AD10 AC11 AA11 AE15 AD15 AA16 AF15 AC16...
- Page 15 SS01-71080-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM DSU-FR EMULATOR LQFP-176P HEADER TYPE5 MB2198-703-E OPERATION MANUAL February 2008 the first edition Published FUJITSU LIMITED Electronic Devices Edited Strategic Business Development Dept.